Sam Cook MASTERCHEF LINE TERMOROBOT WiFi PSC-11 User Manual page 36

3. Place the bowl (8) on the base unit (11) so
that the pins at the bottom of the bowl ad-
just to recesses in the base unit (picture 2).
4. Put one of the accessories on the installed
shaft (25) (Fig.3).
lightweight pulp- butterfly mixer (4)

mixer (5)

knife (6)

strainer (7).

ATTENTION! The knife blades are sharp. Be
careful not to get hurt!
FITTING/REMOVING THE STEAMER CONTAINER
1. Follow the steps described in point 1-3
in the section FITTING/REMOVING THE
BOWL.
2. Make sure that the seal (24) is proper-
ly seated in the steamer container (23).
It must evenly adhere around its entire
circumference to the outside of the ring in
the container.
FITTING/REMOVING THE GRATING/SLICING
1. Follow the steps described in point 1-3
in the section FITTING/REMOVING THE
BOWL. Install the disc mounting stem (18)
on the drive shaft (25).
2. Place the grating/slicing disc (17) with the
appropriate side facing upwards on the
stem (18), depending on the operation
(grating/slicing).
3. Make sure that the seal (16) is properly
seated in the disc cover (15). It must be
3 8
5. Make sure that the seal (3) is properly seat-
ed in the bowl lid (2). It must be properly
seated in the groove for the seal around the
entire circumference.
6. Place the bowl lid (2) on the bowl (8) as
shown in Fig. 4, press it down and turn it
so that the handles of the bowl and the lid
overlap (the tabs in the lid will take their
places in the sockets of the bowl).
7. To remove the bowl from the appliance,
follow these steps:
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3. Place the steamer container (23) on the
bowl (8) as shown in Fig. 6, and turn it so
that the handles of the bowl and the lid
overlap (the tabs in the lid will take their
places in the sockets of the bowl). Place the
tray (22) on the container (23) and cover
the lid (21).
4. To remove the steamer container from the
appliance, follow these steps:
DISC- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
properly seated in the groove for the seal
around the entire circumference.
4. Place the disc cover (15) on the bowl (8)
as shown in Fig. 7, press it down and turn
it so that the handles of the bowl and the
lid overlap (the tabs in the lid will take their
places in the sockets of the bowl).
5. Place the pusher (14) in the disc cover.
6. To remove the disc from the appliance,
follow these steps:
remove the lid (21) and the tray (22)

turn the container (23) slightly counter-

clockwise so that the tabs in the container
slide out of the sockets in the bowl, care-
fully remove the container from the bowl
remove the bowl from the base of the

food processor
remove the knife from the rotary shaft.

Attention! The bowl may be disassembled
only when the lid is removed.
remove the lid (21) and the tray (22)

turn the container (23) slightly counter-

clockwise so that the tabs in the container
slide out of the sockets in the bowl, care-
fully remove the container from the bowl
remove the bowl from the base of the

food processor.
turn the lid (15) slightly counterclockwise

so that the tabs in the lid slide out of the
sockets in the bowl, carefully remove
the lid
remove the bowl from the base of the

food processor
remove the disc (17) from the stem (18)

remove the stem (18) from the rotary

shaft (25).