Subscribe to Our Youtube Channel
Related Manuals for DÖRR EcoGun AS AUTO Mini FS
Summary of Contents for DÖRR EcoGun AS AUTO Mini FS
- Page 1 EcoGun AS AUTO Mini FS Automatic Air Spray Gun Operation manual MSG00006EN, V04 N36210006V www.durr.com...
- Page 2 This document describes the following product: N36210006V EcoGun AS AUTO Mini FS Hotline and Contact If you have queries or would like technical information, please contact your dealer or sales partner. 2/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023...
-
Page 3: Table Of Contents
Purging......... 13 11.4 Order........32 6.2.1 Safety recommendations... 13 6.2.2 General notes....13 6.2.3 Purging......13 Cleaning and maintenance..13 Safety recommendations..13 Cleaning....... 15 Maintenance......17 7.3.1 Maintenance schedule..17 06/2023 EcoGun AS AUTO Mini FS - MSG00006EN 3/36... -
Page 4: Product Overview
Alignment of the air cap Opens the needle and controls the mate- The alignment of the air cap determines rial flow. the alignment of the spray pattern. Material pressure Atomizer air pressure 4/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023... -
Page 5: Safety
You can also regulate the material flow via the regulator on the spray gun, if it is not to be controlled externally. The EcoGun AS AUTO Mini FS spray gun is only intended for use in industry and craft- manship. -
Page 6: Residual Risks
Ensure that forced ventilation and fire Ensure that static electricity can be dis- protection equipment are in operation. charged. Do not use sources of ignition and open light. Do not smoke. Ground the spray gun. 6/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023... -
Page 7: Staff Qualification
Introduce measures in the event of faults. in the work area. Clean system/ product. Hot surfaces During operation, the surfaces of compo- nents can get extremely hot. Contact with it can cause burns. 06/2023 EcoGun AS AUTO Mini FS - MSG00006EN 7/36... -
Page 8: Personal Protective Equipment
Do not expose to aggressive media. Use ear protection Protect from solar radiation. Protects from auditory damage due Avoid mechanical vibrations. to noise. Temperature: 10°C to 40°C Relative humidity: 35% to 90% 8/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023... -
Page 9: Assembly
– Horn air with connection for external jet control: Ø6mm push-in connector (M5 thread in the pistol housing) WARNING! Sources of ignition may cause explo- sions! Ensure a non-explosive atmosphere. 06/2023 EcoGun AS AUTO Mini FS - MSG00006EN 9/36... - Page 10 3. Tighten the connection for jet control. 3 - Control air 4. Connect horn air line to the connection of the jet control. Connect the external jet control connec- tion Protective equipment: Protective workwear Protective gloves 10/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023...
-
Page 11: Setting The Spray Jet
Protective gloves Depending on the design of the application system, two technicians must be present to execute the commissioning: Technician 1: Operates the controls. Technician 2: Check on the spray gun. 06/2023 EcoGun AS AUTO Mini FS - MSG00006EN 11/36... -
Page 12: Operation
Via valves in the control cabinet when using the connection for external jet control ð When the horn air is blocked, the spray pattern is round. 12/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023... -
Page 13: Purging
Protective equipment: Do not use sources of ignition and open light. Use ear protection Do not smoke. Eye protection Check grounding. Respiratory protection device Protective workwear Protective gloves 06/2023 EcoGun AS AUTO Mini FS - MSG00006EN 13/36... - Page 14 Remove dried non-flammable coating spray gun is installed, from com- materials using a material manufacturer- pressed air and material supply. approved organic thinner. Secure system personalized from being switched on again. Depressurize the lines. 14/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023...
-
Page 15: Cleaning
Do not use any thinner spray guns. the spray gun. Dry with a soft cloth. Do not use high pressure for cleaning agents. Cleaning the air cap und nozzle Fig. 8: Clean spray gun 06/2023 EcoGun AS AUTO Mini FS - MSG00006EN 15/36... - Page 16 Carefully push in distance bolt (5) with needle (7) and locknut (6) into the housing. 17. Insert needle spring (3) and plunger spring (4). 18. Twist in bolt (2). 19. Twist in the control knob (1). 16/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023...
-
Page 17: Maintenance
Rotate air cap into the required posi- Air cap is misaligned. tion Ä 4.3 “Setting the spray jet”. Reduce material feed. Spray jet too strong in Too much material center Increase atomizer air pressure. 06/2023 EcoGun AS AUTO Mini FS - MSG00006EN 17/36... - Page 18 Infeed line pinched or Check infeed line. broken Check Control air. Check operation of needle. Replace Needle does not fully needle, if defective, together with the open. nozzle Ä 8.2.1 “Replace needle and nozzle.”. 18/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023...
-
Page 19: Troubleshooting
Replacing only the needle or only the nozzle could damage spray gun compo- nents. This can compromise the tightness of the spray gun. The spray pattern deteri- orates. 06/2023 EcoGun AS AUTO Mini FS - MSG00006EN 19/36... - Page 20 7. Remove the manifold (9). 20. Insert needle spring (3) and plunger spring (4). 8. Unscrew and remove nozzle (8). 21. Twist in bolt (2). 22. Twist in the control knob (1). 20/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023...
-
Page 21: Replace Needle Seal
Mechanical load can damage needle. Handle with care during installation and dismantling. Do not subject the needle to any mechanical pressure. Avoid collisions of components to be assembled and disassembled with the needle. 06/2023 EcoGun AS AUTO Mini FS - MSG00006EN 21/36... - Page 22 14. Twist in the control knob (1). 8. Use a cleaning agent to clean the contact face of the needle seal. 15. Fit cover (9). Let components engage. Assembly 9. Insert new needle seal (8). 22/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023...
-
Page 23: Set Delay Time
If in doubt, contact Dürr Systems Ä “Hotline and Contact”. Disassembly 1. Unscrew the control knob (1). 06/2023 EcoGun AS AUTO Mini FS - MSG00006EN 23/36... -
Page 24: Disassembly And Disposal
Turn it to the left to increase the delay time. Depressurize the lines. The recommended distance from the distance bolt (5) to the piston (8) is 0.3 to 0.5mm. 24/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023... -
Page 25: Disassembly
3. Disconnect all lines. according to the disposal provisions in 4. Disassemble the spray gun from the sup- force. port bracket. In case of doubt, refer to the local dis- posal authorities. 06/2023 EcoGun AS AUTO Mini FS - MSG00006EN 25/36... -
Page 26: Technical Data
Control air pressure 3.5-5bar 10.2 Connections Material pressure, max. 1.5bar Connection Nominal width Ø6 mm (G1/8” Material thread in pistol housing) Control and atomizer Ø6 mm (M5 thread in pistol housing) 26/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023... -
Page 27: Type Plate
10.9 Material specification Product name Suitable Material: Material number Flammable and inflammable coating Year of manufacture materials Serial number Ex labeling Do not use halogen - hydrocarbon Manufacturer based material. CE labeling 06/2023 EcoGun AS AUTO Mini FS - MSG00006EN 27/36... -
Page 28: Spare Parts, Tools And Accessories
Spare parts, tools and accessories Spare parts, tools and accessories 11.1 Spare parts Fig. 14: Exploded view Klüber Syntheso GLEP1 Item Denomination Quantity Material no. Seal M08130069 Slip ring 28/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023... - Page 29 O-ring 10 x 2 M08030862 Piston Catch Screw Jet control M21210004 Scale plate External jet control connection Ä 11.3 “Accessories” 1 Ä “Overview - Air Needle caps and nozzles” Locknut N36960117 06/2023 EcoGun AS AUTO Mini FS - MSG00006EN 29/36...
- Page 30 15, 16, 29, 30 M09800063 1.0mm M09800064 Catch set N36960118 Description Item no. Quantity Screw 12, 25 Catch Catch Scale plate set M44510177 Description Item no. Quantity Scale plate Scale plate 30/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023...
-
Page 31: Tools
Seal Slip ring Compression spring Cap nut O-ring 3.6 x 2 Cover 11.2 Tools Maintenance kit: Denomination Material number Special key SW 6/7 Extension rod for special key N36960017 Cleaning brush 06/2023 EcoGun AS AUTO Mini FS - MSG00006EN 31/36... -
Page 32: Accessories
Serious injury and death could be the con- sequence. Use exclusively original spare parts. Ordering spare parts, tools and accessories as well as information on products that are listed without order number Ä “Hotline and Contact”. 32/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023... - Page 33 06/2023 EcoGun AS AUTO Mini FS - MSG00006EN 33/36...
- Page 34 34/36 EcoGun AS AUTO Mini FS - MSG00006EN 06/2023...
- Page 35 06/2023 EcoGun AS AUTO Mini FS - MSG00006EN 35/36...
- Page 36 Dürr Systems AG Application Technology Carl-Benz-Str. 34 74321 Bietigheim-Bissingen Germany Phone +49 7142 78-0 www.durr.com Translation of the original operation manual MSG00006EN, V04 No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or otherwise, without the prior written permission of the copyright owner.
Need help?
Do you have a question about the EcoGun AS AUTO Mini FS and is the answer not in the manual?
Questions and answers