Subscribe to Our Youtube Channel
Related Manuals for DÖRR EcoGun AS AUTO Mini RS
Summary of Contents for DÖRR EcoGun AS AUTO Mini RS
- Page 1 EcoGun AS AUTO Mini RS Automatic Air Spray Gun Operation manual MSG00007EN, V03 www.durr.com N36210007V...
- Page 2 Validity range of the document This document describes the following product: N36210007V EcoGun AS AUTO Mini Hotline and Contact If you have queries or would like technical information, please contact your dealer or sales partner. 2/28 EcoGun AS AUTO Mini RS - MSG00007EN 11/2016...
-
Page 3: Table Of Contents
Cleaning and maintenance..10 Safety recommendations..10 Cleaning....... 11 Maintenance......12 7.3.1 Maintenance schedule..12 Faults........... 13 Defects table......13 Troubleshooting....14 8.2.1 Replace needle and nozzle........ 14 8.2.2 Replace needle seal..16 11/2016 EcoGun AS AUTO Mini RS - MSG00007EN 3/28... -
Page 4: Product Overview
The higher the material pressure, the WARNING! higher the material flow Medium risk situation that can lead to Control air pressures and the atomizer pres- serious injuries or death. sure are controlled externally via valves. 4/28 EcoGun AS AUTO Mini RS - MSG00007EN 11/2016... -
Page 5: Intended Use
Intended Use for safe operation: Ground spray gun and work piece. Only use conductive lines. The EcoGun AS AUTO Mini RS spray gun is Ensure that static electricity can be dis- intended for use in application stations only. charged. The EcoGun AS AUTO Mini RS spray gun is... -
Page 6: Staff Qualification
– Observe local disposal specifica- components can get extremely hot. Burn tions. injuries can happen on contact. Before carrying out any work: Check the temperature. Do not touch hot surfaces. Let components cool down. 6/28 EcoGun AS AUTO Mini RS - MSG00007EN 11/2016... -
Page 7: Storage
Control air and atomizer air: Ø6 mm push-in connector (M5 thread) Material connection: Ø6 mm push-in connector (G1/8” thread) WARNING! Sources of ignition may cause explo- sions! Ensure a non-explosive atmosphere. 11/2016 EcoGun AS AUTO Mini RS - MSG00007EN 7/28... -
Page 8: Commissioning
Connect lines. Ensure correct assign- ment. 1 - Material 2 - Atomizer air 3 - Control air Commissioning Protective equipment: Use ear protection Eye protection Respiratory protection device Protective workwear Protective gloves 8/28 EcoGun AS AUTO Mini RS - MSG00007EN 11/2016... -
Page 9: Operation
– Use only the rinsing agents that are compatible with the components and the material. – Refer to safety data sheet of mate- rial manufacturer. 6.2.2 General notes When rinsing, use fluid to remove inner soiling from components. 11/2016 EcoGun AS AUTO Mini RS - MSG00007EN 9/28... -
Page 10: Rinsing
– Relieve the lines. – Do not use any sources of ignition and no open light. – Do not smoke. – Observe the safety data sheets. 10/28 EcoGun AS AUTO Mini RS - MSG00007EN 11/2016... -
Page 11: Cleaning
2. Use a cleaning agent to carefully clean Use alcohols (isopropanol, butanol) for the atomizer. Dry with a soft cloth. water-based paint. Remove dried water-based paint residue using a manufacturer approved thinner. 11/2016 EcoGun AS AUTO Mini RS - MSG00007EN 11/28... -
Page 12: Maintenance
Daily lines. Check fastening Clean Ä 7.2 “Cleaning”. Before every change of material Remove and lubricate piston Ä 8.2.2 “Replace needle monthly seal” Check grounding Ä 4.2 “Assembly” after each alteration 12/28 EcoGun AS AUTO Mini RS - MSG00007EN 11/2016... -
Page 13: Faults
Ä 8.2.1 “Replace needle and nozzle.”. Material pressure too low. Increase material pressure. Feed line pinched or Check the feed line. broken. Needle does not open Check control air. fully. 11/2016 EcoGun AS AUTO Mini RS - MSG00007EN 13/28... -
Page 14: Troubleshooting
Formation of large drops Delay time for atomizer air Set delay time Ä 8.2.3 “Set delay supply too short. time”. Troubleshooting 8.2.1 Replace needle and nozzle. Fig. 6: Replace needle and nozzle. Protective equipment: Protective workwear Protective gloves 14/28 EcoGun AS AUTO Mini RS - MSG00007EN 11/2016... - Page 15 16. Insert needle spring (3) and plunger spring (4). spring (4). 4. Pull out distance bolt (5) and needle (8) 17. Thread in bolt (2). and locknut (6). 18. Thread in the control knob (1). 11/2016 EcoGun AS AUTO Mini RS - MSG00007EN 15/28...
-
Page 16: Replace Needle Seal
– Avoid collisions of components to be 9. Pull back spring (6). Put the slip ring (7) assembled and disassembled with in place. the needle. Disassembling 1. Thread off control knob (1). 2. Thread off bolt (2). 16/28 EcoGun AS AUTO Mini RS - MSG00007EN 11/2016... -
Page 17: Set Delay Time
– You should only change the delay time upon inserting a new needle or in case there are problems with the spray pattern. – If in doubt, contact Dürr Systems Ä “Hotline and Contact”. 11/2016 EcoGun AS AUTO Mini RS - MSG00007EN 17/28... -
Page 18: Disassembly And Disposal
Turn it to the left to increase the delay time. The recommended distance from the distance bolt (5) to the piston (9) is 0.3 to 0.5 7. Tighten the lock nut (6). 18/28 EcoGun AS AUTO Mini RS - MSG00007EN 11/2016... -
Page 19: Disassembly
Control and atom- Ø6 mm Push-In izer air (M5-threads) Minimum cross section The minimum dimensions required for the cross section of the air and material feed lines are as follows: 11/2016 EcoGun AS AUTO Mini RS - MSG00007EN 19/28... -
Page 20: Operating Conditions
Control air pressure, max. 5 bar Materials in contact Stainless steel/ with material nickel plated alu- Material pressure, max. 1.5 bar minum Seals in contact PTFE with material Seals without mate- rial contact 20/28 EcoGun AS AUTO Mini RS - MSG00007EN 11/2016... -
Page 21: Material Specification
Do not use halogen - hydro- carbon based material. Suitable material: Water-based or solvent based paints Replacement parts, tools and accessories 11.1 Replacement parts Fig. 11: Exploded view Klüber Syntheso GLEP 1 11/2016 EcoGun AS AUTO Mini RS - MSG00007EN 21/28... - Page 22 M08030859 O-Ring 15 x 1 M08030863 Bushing insert O-Ring 6.75 x 1.78 M08030860 O-Ring 10 x 2 M08030862 Piston Needle Locknut Distance bolt Needle spring Plunger spring Bolt Control knob M21030002 22/28 EcoGun AS AUTO Mini RS - MSG00007EN 11/2016...
- Page 23 Compression spring O-Ring 3.6 x 2 Piston set N36960082 Description Item Quantity O-Ring 6 x 1.5 O-Ring 15 x 1 Bushing insert O-Ring 6.75 x 1.78 O-Ring 10 x 2 Piston 11/2016 EcoGun AS AUTO Mini RS - MSG00007EN 23/28...
- Page 24 Quantity Needle spring Plunger spring Needle holder N36960117 Denomination Item Quantity Locknut Distance bolt Needle guide set N36960120 Denomination Item Quantity Seal Slip ring Compression spring Bushing O-Ring 3.6 x 2 24/28 EcoGun AS AUTO Mini RS - MSG00007EN 11/2016...
- Page 25 Extensions 100 mm Item Denomination Material no. 1, 2, 3, 4, 5, 6, 7, 8 Nozzle 0.6 mm M19140006 Nozzle 0.8 mm M19140007 Nozzle 1.0 mm M19140008 Nozzle 1.2 mm M19140009 11/2016 EcoGun AS AUTO Mini RS - MSG00007EN 25/28...
-
Page 26: Accessories
– Use exclusively original replacement parts. Ordering replacement parts, tools and accessories as well as information on prod- ucts that are listed without order number. Ä “Hotline and Contact” 26/28 EcoGun AS AUTO Mini RS - MSG00007EN 11/2016... - Page 27 11/2016 EcoGun AS AUTO Mini RS - MSG00007EN 27/28...
- Page 28 Dürr Systems AG Application Technology Carl-Benz-Str. 34 D-74321 Bietigheim-Bissingen Tel.: +49 7142 78-0 www.durr.com Original operation manual Transmission and duplication of this document, as well as use and sharing of its contents are not permitted without express written approval. Violations will be liable for compensation for damages. All rights in the event of a patent grant or design registration are reserved.
Need help?
Do you have a question about the EcoGun AS AUTO Mini RS and is the answer not in the manual?
Questions and answers