Subscribe to Our Youtube Channel
Related Manuals for Godex DT200+ Series
Summary of Contents for Godex DT200+ Series
- Page 1 DT200(i)(L)+ Series DT200(i)(L)+ Series User Manual P/N:920-019711-00 Version: A.2 Issue date:2023/08/31...
- Page 2 ..................................5 ....................................5 ..............................6 ......................................9 ............9 ..............................13 ....................... 14 ........................... 15 ................................20 .............................. 20 ..........................21 ....................................22 ..................... 23 .......................... 28 ........................30 ....................32 ....................36 .......................... 37 ....................................39 ................................41 ............................
- Page 3 FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
- Page 4 ⚫ ⚫ ⚫ ⚫...
- Page 5 DT200L+ Series DT200iL+ Series DT200+ Series DT200i+ Series ※Package content may vary per region. ‧ Power cord ‧ USB cable ‧ Power adapter ‧ DT200+ Quick guide ‧ *Peel detection board *Only for DT200L+/DT200iL+ Series...
- Page 6 Top cover LCD panel Power button Direction key Feed button Cover release catches Front cover FAN-FOLD LABEL INSERT USB port USB Host Power jack Ethernet port Calibration Button Serial port...
- Page 7 Mounting points Bottom cover ※...
- Page 8 Print mechanism Print head release lever Release catch Label roll holder Label supply hub Label guides Label sensor *Roller fixed latch Platen roller...
- Page 9 Place the printer on a flat surface and open the printer cover. Release the label supply hub.
- Page 10 Lift the label roll holder and pull it out as far as possible. Install the label roll on the label supply hub.
- Page 11 Now press the label roll holder down until it clicks into place. Pass the label under the paper guides and pull it forward.
- Page 12 Adjust the paper guides to the width of the label liner. Close the printer cover to finish loading the labels...
- Page 13 1. Pull the label roll holder out as far as it will go. 2. Fold out the label supply hub as shown in the illustration. 3. Now rotate the label roll holder to return the label supply hub to its original position.
- Page 22 ⚫ ⚫ ⚫...
- Page 23 Power on Enter Main page...
- Page 24 Select Enter Select 旋轉 Enter...
- Page 25 Select Apply ⚫ ⚫...
- Page 26 NAVIGATION ICON Back to the Setting page Back to the Main page...
- Page 27 EXIT from Setting Mode Back to the Ready status...
- Page 28 ， Select Device Enter LAN Setting ， Select a designated funcition...
-
Page 29: Setting Page
Select ↓ to enable DHCP Press FEED once to exit. Press FEED again to save and return to previous SETTING PAGE... - Page 30 Select Device Enter LCD Password Select ↓ button to Enable Password function...
- Page 31 Select ↓ button again to setup the password Press FEED button onece to exit. Press FEED button again to save and return to previous SETTING PAGE...
- Page 33 繁體中文 简体中文...
-
Page 36: Error Icon
WARNING ICON ERROR ICON ERROR DESCRIPTION... - Page 37 OPERATION LCD Screen PANEL Feed key Power Button Direction key...
- Page 51 ※ Swipe across the surface of Swipe across the surface of Open the cutter cover. cutter with a soft lint- free cutter with a soft lint- free cloth or cotton bud cloth or cotton bud...
- Page 52 ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫...
- Page 53 、 、 、 、 、 、...
- Page 54 、 、 、 、 、 、...
- Page 55 ⚫ ⚫ ⚫ ⚫...
- Page 56 ⚫ ⚫ ● ●...
- Page 57 Set up wireless network through GoDEX WiFi tool 1. Turn on the printer,connect printer and computer by USB cable. 2. Start GoLabel II “Generic”→”Printer Setup”. 4. Select printer moedel(Wi-Fi supported models).
- Page 58 Click”WiFi Setting”icon. Click”Quick Setting”icon.
- Page 59 7. Click the Search button.
- Page 60 8. Select server and click next button. 9. Enter the password set on the server side and click the “Setting” button.
- Page 61 10. After the setting succeeded, a prompt will pop up and the printer will restart. 11. Select the "Other" tab and selecting "IP Settings" after click the "Get Data" icon.
- Page 62 12. After remembering the IP address, open the "Printer Settings" window. elect the“Printer Interface”tab, fill in the IP address and click “Save” to complete the setting.
- Page 63 BT module setting instructions (Connect to mobile phone) * Android applies to BT2.1 and 4.0 iOS only works with BT4.0 First pair the phone with the printer Turn on the printer and wait for it to enter the “Ready” state. Select the printer model you want to connect.
- Page 64 Select connection method and printer For the connection method, choose “Near BT” button. The printers which installed the BT module will be listed below, select the printer to connect. 6. If the connection is successful, the function window will be displayed. * When using the BT4.0 module, you need to use GoLabel to send the command "^XSET,EXTERNCARDMODE,8"...
Need help?
Do you have a question about the DT200+ Series and is the answer not in the manual?
Questions and answers