Table of Contents
Advertisement
Quick Links
Outdoor Super Pro 60"
Installation Guide
For Model:
OS60
net weight of fan: 22.77 lb. (10.33 kg)
READ THESE INSTRUCTIONS
AND SAVE THEM FOR FUTURE USE
Table of Contents:
Safety Tips. pg. 2
Unpacking Your Fan. pg. 3
Parts Inventory. pg. 3
Installation Preparation. pg. 4
Hanging Bracket Installation. pg. 4
Fan Assembly. pgs. 5 - 6
Wiring. pg. 7
Canopy Assembly. pg. 7
Blade Assembly. pg. 8
Testing Your Fan. pg. 9
Troubleshooting. pg. 10
Parts Replacement. pg. 10
Warranty. pg. 10
page 1
PRINTED IN CHINA
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Craftmade OS60
Summary of Contents for Craftmade OS60
-
Page 1: Table Of Contents
READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Outdoor Super Pro 60” Installation Guide For Model: OS60 Table of Contents: Safety Tips. pg. 2 Unpacking Your Fan. pg. 3 Parts Inventory. pg. 3 Installation Preparation. pg. 4 Hanging Bracket Installation. pg. 4 Fan Assembly. -
Page 2: Safety Tips
Distributed by: Craftmade, 3901 South 20th Avenue, DFW Airport, TX, 75261; 1-800-486-4892 NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all possible conditions and situations that may occur. -
Page 3: Unpacking Your Fan
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. -
Page 4: Installation Preparation
3. Installation Preparation. blade edge To prevent personal injury and damage, ensure that inches the hanging location allows the blades a clearance 7 feet (76 cm) of 7 feet (2.13m) from the floor and 30in. (76cm) (2.13m) from any wall or obstruction. This fan is suitable for room sizes up to 12ft. -
Page 5: Fan Assembly. Pgs
5. Fan Assembly. stop pin set screw Remove hanging ball from downrod provided by loosening set screw on hanging ball. Lower hanging hanging ball ball and remove stop pin and then slide hanging ball off of the downrod. [Refer to diagram 1.] Loosen yoke set screws and nuts at top of motor diagram 1 housing. - Page 6 5. Fan Assembly. (cont.) Remove electrical tape from electrical wiring and weatherproof thread each of the wires through a different hole hanging in the weatherproof hanging ball cover. Pull ball cover weatherproof hanging ball cover down securely over hanging ball (on downrod). [Refer to electrical wiring diagram 5.] set screw hole...
-
Page 7: Wiring
6. Wiring. WARNING: Turn off circuit breakers to current white supply wire fixture from breaker panel and be sure switch is ground turned to the OFF position. (green or bare) black supply wire CAUTION: Be sure outlet box is properly grounded and that a ground wire (GREEN or Bare) is present. -
Page 8: Blade Assembly
8. Blade Assembly. WARNING: To reduce the risk of serious bodily blade attachment screws/washers injury, DO NOT use power tools to assemble the blades. If screws are overtightened, blades may motor housing crack and break. Time Saver: Washers for blade screws can be set on each blade screw prior to installing blades. -
Page 9: Testing Your Fan
9. Switch Housing Assembly. (cont.) Remove 3 screws from outer edge of switch motor housing plate (save screws for later use). housing Connect male plug from motor housing to female plug from switch housing, matching up the colors on the male plug with the colors on the female switch plug for correct fit. -
Page 10: Troubleshooting
Contact Craftmade Customer Solutions: Service at 1-800-486-4892 to arrange for return of fan. Return fan, shipping prepaid, to Craftmade. We will repair 1. Check wall switch to fan. or ship you a replacement fan, and we will pay the return 2.
Need help?
Do you have a question about the OS60 and is the answer not in the manual?
Questions and answers