Craftmade BC52 Installation Instructions Manual

Craftmade BC52 Installation Instructions Manual

Decorative ceiling fans
Hide thumbs Also See for BC52:
Table of Contents

Advertisement

Available languages

Available languages

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BC52 and is the answer not in the manual?

Questions and answers

Summary of Contents for Craftmade BC52

  • Page 2: What You Have

    Read and Save These Safety Precautions What You Have Turn off electricity at main switch before wiring or servicing fan in order to avoid Parts Quantity possible electrical shock. All wiring must be in accordance with the National Electric Code (ANSI/NFPA 70- 1.
  • Page 3 B. Angle Mount Downrod Installation (Normal Ceilings) Canopy Screws (S2) Craftmade Part #45AD (see dealer) IMPORTANT: If using the angle mount Step 5 method, check to make sure the ceiling angle is not steeper than 35 . Angles greater than...
  • Page 4 Step 6 Step 7 Position downrod so the hole in the downrod aligns with the hole in the For added security, attach safety cable from fan unit to "J" hook (S9) in coupling on the motor. Insert safety bolt (S7) through coupling and downrod outlet box.
  • Page 5: Wiring

    Step 8 Step 9 1. Connect fan wires to ceiling wires: white fan wire to white outlet wire, Attach canopy (3) to the Ceiling black to black and green to green. Wire connectors (S6) are provided for mounting bracket by placing your convenience.
  • Page 7: Electrical Connections

    Electrical Connections Continued… Electrical Connections Connect black and blue (if provided) fan wires to black outlet wire. Connect white fan wire to white outlet wire and green grounding lead wire from the Ground grounding conductor to the supply circuit (see figure A). Use wire connectors provided with your fan.
  • Page 9: Componentes Incluidos

    Lea y conserve estas precauciones de seguridad Componentes Incluidos 1. Apague la electricidad con el interruptor principal antes de cablear o dar servicio al Piezas Cantidad ventilador para evitar posibles choques eléctricos. 2. Todo el cableado eléctrico debe acatar los códigos eléctricos nacionales (ANSI/NFPA 1.
  • Page 10 Determine el método de montaje a usar. A. Montaje con vara hacia abajo B. Montaje angular Tornillos para madera (S1) Tornillos para madera (S1) Pieza Craftmade 45AD Tornillos para Instalación con vara hacia abajo (cielos rasos normales) la cúpula (S2) (consulte al distribuidor) IMPORTANTE: Si utiliza el método de montaje...
  • Page 11 Paso 6 Paso 7 Sitúe la vara hacia abajo de manera que el agujero en la misma quede alineado Para mayor seguridad, instale un lazo de alambre de acero desde el ventilador con el agujero en el acoplamiento del motor. Inserte el perno de seguridad (S7) al gancho “J”...
  • Page 12 Paso 9 Paso 8 Cielo raso Instale la cúpula (3) en el soporte 1. Conecte los cables del ventilador a los del techo: el cable blanco del ventilador de montaje colocando los tornillos con el cable blanco de salida, negro con negro y verde con verde. Se incluyen los (S2) en la ranura de la cúpula.
  • Page 14: Conexiones Eléctricas

    Conexiones eléctricas Continuación… Conexiones eléctricas Conecte los cables negro y azul (si se incluyen) al cable de salida negro. Conecte el cable blanco del ventilador con el cable de salida blanco y el cable conductor Tierra de tierra verde desde el conductor de tierra al circuito de suministro (consulte la figura A).
  • Page 16: Composants Inclus

    Veuillez lire et conserver ces consignes de sécurité Composants inclus 1. Pour éviter de vous électrocuter, débranchez l'alimentation électrique au niveau de l'interrupteur principal avant de procéder au câblage ou à l'entretien du ventilateur. Pièces Quantité 2. Tout le câblage doit être effectué en accord avec le code électrique national américain (ANSI/NFPA 70-1999) et les codes électriques locaux.
  • Page 17 Vis à bois (S1) Vis à bois (S1) B. Montage sur une surface inclinée Vis de coupelle (S2) Pièce Craftmade n 45AD (consultez votre revendeur) Étape 5 IMPORTANT: si vous utilisez la méthode de montage inclinée, vérifiez que l'angle du plafond est inférieur à...
  • Page 18 Étape 6 Étape 7 Placez la tige de suspension de manière à ce que son trou soit aligné avec Pour plus de sécurité, attachez le câble de sécurité du ventilateur au crochet celui de l’attelage du moteur. Insérez le boulon de sécurité (S7) dans l’attelage en «...
  • Page 19 Étape 8 Étape 9 1. Connectez les fils du ventilateur à ceux du plafond : le fil de ventilateur Fixez la coupelle (n 3) au support Plafond blanc au fil de sortie blanc, le fil noir au fil noir et le fil vert au fil vert. Les de montage en insérant les vis connecteurs (S6) sont fournis au cas où...
  • Page 21: Connexions Électriques

    Mode d'emploi Connexions électriques 1. La séquence de fonctionnement de la chaîne de traction/interrupteur du Branchez les fils bleu et noir du ventilateur (s’ils sont fournis) sur le fil noir de la boîte de sortie. Connectez le fil blanc du ventilateur au fil blanc de la boîte de moteur est OFF-HI-MED-LOW.

Table of Contents