c) Prevent unintentional starting. Ensure the GENERAL POWER TOOL SAFETY switch is in the off -position before connecting WARNINGS to power source and/or battery pack, picking up or carrying the tool. WARNING Carrying power tools with your fi nger on the switch Read all safety warnings, instructions, illustrations and or energising power tools that have the switch on specifi...
h) Keep handles and grasping surfaces dry, clean Safety instructions when using long drill bits and free from oil and grease. a) Never operate at higher speed than the maximum Slippery handles and grasping surfaces do not speed rating of the drill bit. allow for safe handling and control of the tool in At higher speeds, the bit is likely to bend if allowed to unexpected situations.
18. The motor rotation may be locked to cease while the unit 2. Do not pierce battery with a sharp object such as a is used as drill. While operating the driver drill, take care nail, strike with a hammer, step on, throw or subject the not to lock the motor.
Page 5
SYMBOLS Power Output WARNING The following show symbols used for the machine. Be sure that you understand their meaning before 2 to 3 digit number use. DV18DBFL2: Cordless Combi Drill To reduce the risk of injury, user must read instruction manual. USB DEVICE CONNECTION Only for EU countries PRECAUTIONS (ONLY WITH...
12. Table 1, according to the condition of the charger or the NOTE rechargeable battery. Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to change without prior notice. Table 1 Indications of the pilot lamp Lights for 0.5 seconds.
Page 7
Number of battery cells 4–10 4–10 not cause the pilot lamp to blink in red (every second), please take the charger to the HiKOKI Authorized NOTE Service Center. The recharging time may vary according to temperature and power source voltage.
(2) Regarding the temperatures and charging time of the rechargeable battery The temperatures and charging time will become as shown in Table 4. Table 4 Charger UC18YSL3 Battery Charging voltage 14.4 Type of battery Li-ion Temperatures at which the battery can be 0oC–50oC recharged Charging time for battery capacity, approx.
Since use of as dull tool will degrade effi ciency and cause possible motor malfunction, sharpen or replace the tool as soon as abrasion is noted. Important notice on the batteries for the HiKOKI 2. Inspecting the mounting screws cordless power tools...
Uncertainty K = 1.5 m/s Impact drilling into concrete: NOTE Vibration emission value , ID = 9.1 m/s Due to HiKOKI’s continuing program of research and Uncertainty K = 1.5 m/s development, the specifi cations herein are subject to change without prior notice. TROUBLESHOOTING Use the inspections in the table below if the tool does not operate normally.
Page 11
The charger’s vents are blocked, causing its Avoid blocking the vents. internal components to overheat. The cooling fan is not running. Contact a HiKOKI Authorized Service Center for repairs. <UC18YSL3 only> Charging of a USB device The charger was plugged into an electrical This is not a malfunction.
Date of Purchase Customer Name and Address Dealer Name and Address (Please stamp dealer name and address) Hikoki Power Tools (U.K.) Ltd. Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ, United Kingdom Tel: +44 1908 660663 Fax: +44 1908 606642...
Page 24
EN60335-1:2012+A11:2014 EN60335-2-29:2004+A2:2010 EN55014-1:2006+A1:2009+A2:2011 EN55014-2:1997+A1:2001+A2:2008 Importer and authorized person to compile the technical fi le Hikoki Power Tools (U.K.) Ltd. Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ, United Kingdom 30. 6. 2021 Head offi ce in Japan Koki Holdings Co., Ltd.
Need help?
Do you have a question about the DV 18DBFL2 and is the answer not in the manual?
Questions and answers