Woodstock Shop Fox W1755H Manual page 22

300
DANGER!
ROTATING
CUTTERHEAD BELOW!
WARNING! WARNING!
KICKBACK HAZARD! ALWAYS USE
1. Ensure outfeed table is PUSH BLOCKS!
Use this guard for all
even with knives.
Push blocks minimize the
operations possible, and
2. Never exceed the
possibility of operator's
immediately reinstall it
maximum depth of cut.
hands contacting the
following operations that
3. Do not stand directly
require its removal. cutterhead while cutting.
behind workpiece.
306
WARNING! 312
READ
MANUAL
before using
this equipment!
303
WARNING!
WEAR
SAFETY GLASSES
313
or face shield when
using or adjusting
this equipment!
MODEL W1755H
6" PARALLELOGRAM JOINTER
w/HELICAL CUTTERHEAD
WARNING!
Specifications
Motor: 1-1/2 HP, 120V/240V, 1-Ph, 60 Hz
To reduce the risk of serious injury when using this machine:
Full-Load: 15A @ 120V, 7.5A @ 240V
1. Read and understand owner's manual before operating.
Cutterhead Speed: 4800 RPM 2. Always wear approved eye protection and respirator.
Cutterhead Diameter: 3" 3. Only plug power cord into a grounded outlet.
Cutterhead: Helical w/Indexable Inserts
4. Keep all guards in place and in proper operating condition.
Number of Inserts: 32
5. Never edge-joint stock smaller than 10" long, 3/4" wide, or 1/4" thick.
Maximum Depth of Cut: 1/8" 6. Never face-plane stock smaller than 10" long, 3/4" wide, or 1/2" thick.
Cuts Per Minute: 19,400 7. Always use push blocks when face planing.
Fence Tilt Stops: 45º, 90º, 135º
8. Keep hands at least 12" away from cutterhead.
Table Size: 6" x 55-1/2"
9. Never cut deeper than 1/8" on a single pass.
Weight: 325 lbs. 10. Tie back long hair, roll up sleeves, and DO NOT wear loose clothing, gloves, or
jewelry.
11. Turn motor OFF and disconnect power before changing inserts, adjusting
tables/fence, or servicing.
12. Be aware of "kickback" hazards and how to prevent them.
13. Before starting, ensure tables are adjusted properly, blades are secure, and
jointer is stable.
14. Do not joint boards with cracks, loose knots, or any defects.
15. DO NOT expose to rain or use in wet locations.
16. Always support workpiece against fence and table. Never attempt any
Date operation free-handed.
17. Always feed workpiece against cutterhead rotation. Never move workpiece
backward while feeding.
S/N
18. Prevent unauthorized use by children or untrained users; restrict access or
208624
disable machine when unattended.
Mfd. for Woodstock in China
309
REF PART # DESCRIPTION
300 X1755H300 CUTTERHEAD GUARD LABEL
301 X1755H301 FENCE/CUTTERHEAD LABEL
302 X1755H302 ELECTRICITY LABEL
303 X1755H303 SAFETY GLASSES LABEL
304 X1755H304 EAR PROTECTION LABEL
305 X1755H305 DISCONNECT POWER LABEL
306 X1755H306 READ MANUAL LABEL
Safety labels warn about machine hazards and how to prevent serious personal injury. The owner
of this machine MUST maintain the original location and readability of all labels on this machine.
If any label is removed or becomes unreadable, REPLACE that label before allowing machine to
be operated again. Contact us at (360) 734-3482 or www.woodstockint.com to order new labels.
Labels & Cosmetics
301
Cutterhead
Failure to keep hands clear exposed between Failure to keep hands clear
of cutterhead will result in of cutterhead will result in
these lines.
serious personal injury. serious personal injury.
311
W1755H
-22-
Model W1755H (For Machines Mfd. Since 01/20)
302
WARNING!
DISCONNECT
power before
310
adjustments or
maintenance!
308
REF PART # DESCRIPTION
307 X1755H307 SHOP FOX NAMEPLATE
308 X1755H308 MODEL NUMBER LABEL
309 X1755H309 MACHINE ID LABEL
310 X1755H310 TOUCH-UP PAINT, SHOP FOX WHITE
311 X1755H311 TOUCH-UP PAINT, SHOP FOX BLACK
312 X1755H312 DOUBLE BLACK STRIPE
313 X1755H313 SINGLE BLACK STRIPE
304
CAUTION
ALWAYS WEAR
EAR PROTECTION
WHEN USING THIS
MACHINE!
305
307