Connecting To The Drain; Adjusting The Feet; Electrical Connection - Beko WMB 91242LC User Manual

A
WaRNING:
Models with a single water inlet
should not be connected to the hot water tap. In
such a case the laundry will get damaged or the
product will switch to protection mode and will not
operate.
WaRNING:
Do not use old or used water inlet
hoses on the new product. It may cause stains on
your laundry.
1. Connect the special hoses supplied with the product
to the water inlets on the product. Red hose (left)
(max. 90 ºC) is for hot water inlet, blue hose (right)
(max. 25 ºC) is for cold water inlet.
A
WaRNING:
Ensure that the cold and hot water
connections are made correctly when installing the
product. Otherwise, your laundry will come out hot
at the end of the washing process and wear out.
2. Tighten all hose nuts by hand. Never use a tool
when tightening the nuts.
3. Open the taps completely after making the
hose connection to check for water leaks at the
connection points. If any leaks occur, turn off the
tap and remove the nut. Retighten the nut carefully
after checking the seal. To prevent water leakages
and damages caused by them, keep the taps closed
when the machine is not in use.

2.5 Connecting to the drain

• The end of the drain hose must be directly
connected to the wastewater drain or to the
washbasin.
A
WaRNING:
Your house will be flooded if the
hose comes out of its housing during water
discharge. Moreover, there is risk of scalding due
to high washing temperatures! To prevent such
situations and to ensure smooth water intake
and discharge of the machine, fix the end of the
discharge hose tightly so that it cannot come out.
• The hose should be attached to a height of at least
40 cm, and 100 cm at most.
• In case the hose is elevated after laying it on the
floor level or close to the ground (less than 40 cm
above the ground), water discharge becomes more
difficult and the laundry may come out excessively
wet. Therefore, follow the heights described in the
figure.
7 / EN
• To prevent flowing of dirty water back into the
machine and to allow for easy discharge, do not
immerse the hose end into the dirty water or do not
drive it in the drain more than 15 cm. If it is too long,
cut it short.
• The end of the hose should not be bent, it should
not be stepped on and the hose must not be
pinched between the drain and the machine.
• If the length of the hose is too short, use it by
adding an original extension hose. Length of the
hose may not be longer than 3.2 m. To avoid water
leak failures, the connection between the extension
hose and the drain hose of the product must be
fitted well with an appropriate clamp as not to come
off and leak.

2.6 adjusting the feet

A
WaRNING:
In order to ensure that the product
operates more silently and vibration-free, it must
stand level and balanced on its feet. Balance
the machine by adjusting the feet. Otherwise,
the product may move from its place and cause
crushing and vibration problems.
1. Loosen the lock nuts on the feet by hand.
2. Adjust the feet until the product stands level and
balanced.
3. Tighten all lock nuts again by hand.
A
WaRNING:
Do not use any tools to loosen the
lock nuts. Otherwise, they will get damaged.

2.7 Electrical connection

Connect the product to a grounded outlet protected
by a 16 A fuse. Our company shall not be liable for
any damages that will arise when the product is
used without grounding in accordance with the local
regulations.
• Connection must comply with national regulations.
• Power cable plug must be within easy reach after
installation.
• If the current value of the fuse or breaker in the
house is less than 16 Amps, have a qualified
electrician install a 16 Amp fuse.
Washing Machine / User's Manual