Table of Contents
Advertisement
GB
ERROR MESSAGE
When you turn on the fixture, it will make a reset first. The display may show "XXer" while there are
problems with one or more channels. "XX" stands for channel 1, 2, 3,etc who has the testing sensor for
positioning.
For example, when the display shows "Cyan color Er", it means there is some error in channel 1. If there are
some errors on channel 1, channel 2, channel 5 at the same time, you may see the error message "Cyan
Color Er", "Cyan Color Fine Er ", "PAN Movement 8bit Er" flash repeated for 5 times, and then the fixture will
generate a reset signal, all the stepper reset. If the fixture remain error message after performing reset
more than 3 times, it will detect whether the fixture has more than 3 errors. If the fixture has more than 3
errors (including 3 errors), all the channels can not work properly; but if the fixture has less than 3 errors,
only the channels which have errors can not work properly, others can work as usual.
Color wheel Er
(Color wheel- error) This message will appear after the reset of the fixture if the magnetic-indexing circuit
malfunction (sensor failed or magnet missing) or the stepping-motor is defective (or its driving IC on the
main PCB). The color wheel is not located in the default position after the reset.
PAN- movement Er
(PAN-yoke movement error) This message will appear after the reset of the fixture if the yoke's
magnetic-indexing circuit malfunction (sensor failed or magnet missing) or the stepping-motor is defective
(or its driving IC on the main PCB). The PAN- movement is not located in the default position after the reset.
TILT- movement Er
(TILT-head movement error) This message will appear after the reset of the fixture if the head's
magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the stepping-motor is defective
(or its driving IC on the main PCB). The TILT- movement is not located in the default position after the reset.
Gobo wheel 1 Er
(Gobo wheel 1 - error) This message will appear after the reset of the fixture if the magnetic-indexing circuit
malfunction (sensor failed or magnet missing) or the stepping-motor is defective (or its driving IC on the
main PCB). The Gobo wheel 1 is not located in the default position after the reset.
Gobo Rot 1 Er
(Gobo Rot 1- error) This message will appear after the reset of the fixture if the magnetic-indexing circuit
malfunction (sensor failed or magnet missing) or the stepping-motor is defective (or its driving IC on the
main PCB). The Gobo Rot 1 is not located in the default position after the reset.
Effect Er
(Zoom-error) This message will appear after the reset of the fixture if the magnetic-indexing circuit
malfunction (sensor failed or magnet missing) or the stepping-motor is defective (or its driving IC on the
main PCB). The Effect is not located in the default position after the reset.
CLEANING AND MAINTENANCE
The following points have to be considered during the inspection:
1. All screws for installing the devices or parts of the device have to be tightly connected and must not be
corroded.
2. There must not be any deformations on the housing, color lenses, fixations and installation spots (ceiling,
suspension, trussing).
3. Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances.
4. The electric power supply cables must not show any damage, material fatigue or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled installer
and any safety problems have to be removed.
Disconnect from mains before starting maintenance operation.
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never use alcohol or
solvents.
There are no serviceable parts inside the device except for the lamp. Please refer to the instructions under
"Installation instructions".
Idea Beam 300
CAUTION
２３
SGM
XM350 V1.0 NR
Advertisement
Table of Contents
