Kraus FVS-13800 Installation Manual
Kraus FVS-13800 Installation Manual

Kraus FVS-13800 Installation Manual

Coda single lever vessel faucet

Advertisement

Quick Links

I N S TA L L AT I O N MA N UA L
Coda Single Lever Vessel Faucet
FVS-13800
www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc. I REV. August 11, 2015

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FVS-13800 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Kraus FVS-13800

  • Page 1 I N S TA L L AT I O N MA N UA L Coda Single Lever Vessel Faucet FVS-13800 www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc. I REV. August 11, 2015...
  • Page 2 Thank you for purchasing Kraus We would like to take this opportunity to thank you for your business with Kraus USA. It is our sincere hope that you are completely satisfied with your experience. We welcome any questions or comments you may have, and will be glad to assist you in the future.
  • Page 3: Prior To Installation

    Prior to Installation: • Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775- 0703 for a replacement • Turn off the hot and cold water supply at the angle stops and turn on the old 1 1/4-18UNF-2A faucet to release any built up pressure.
  • Page 4 FVS-13800 Diagram and Parts List A. Faucet Body B. Base O-Ring C. Rubber Washer D. Metal Washer E. Mounting Nut F. Mounting Screws G. Hot & Cold Waterlines H. Aerator Assembly H1. Aerator Washer H2. Aerator H3. Aerator Cover I. Hex Wrench...
  • Page 5 Faucet Dimensions º 5 3/8” ∅48 ∅1 7/8” ∅33~∅35 ∅1 5/16”~∅1 3/8”...
  • Page 6 Step1: Install mounting hardware and waterlines Remove mounting nut (E) with mounting screws (F) attached. Remove metal washer (D), and rubber washer (C) from threaded mounting pipe. Place faucet body (A) on a soft cloth, spout facing up. Secure the hot & cold waterlines (G) at the base of the faucet (HAND-TIGHTEN ONLY) A.
  • Page 7 Step 3: Secure faucet After adjusting direction of faucet body (A), tighten mounting nut (E) with adjustable wrench until snug. Secure mounting nut (E) by tightening mounting screws (F) with a Phillips head screwdriver Step 4: Connect waterlines to faucet and main valve Thread hot &...
  • Page 8 Remove aerator (H2) and aerator washer (H1). Turn water on for 1 minute to remove any debris. Reassemble aerator assembly (H) Replacement Part List - FVS-13800 1. Metal Handle 2. Set Screw 3. Cover Button 4. Cartridge Cover 5.
  • Page 9: Troubleshooting

    Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: P R O B L E M C A U S E A C T I O N Leakage under the Locking nut (5) has Remove cover button...
  • Page 10: Conditions And Exclusions

    If Kraus is unable to provide a replace- ment and repair is not practical or cannot be made in timely fashion, Kraus may elect to refund the purchase price in exchange for the return of the product.
  • Page 11 NON-APPLICABILITY OF THIS WARRANTY By the purchase and use of our products, you agree that Kraus is not liable for incidental, consequential or special damages associated with the return, replacement, installation or use of your product. This includes freight costs, cartridge replacement, labor, travel time,...
  • Page 12 www.kraususa.com...

This manual is also suitable for:

Fvs-13800-pu-10ch

Table of Contents