Table of Contents
Advertisement
3-8-2 Backlight Setting
(1) Touch the [Backlight Setting]
on the "Preference" screen.
Enable or disable the backlight
(2) "Backlight Setting" screen is displayed. Touch the [En-
able/Disable] on the "Backlight Setting" screen.
(3) "Enable/Disable" screen is displayed. Select the [Enable]
or [Disable].
(2)
Backlight Setting
Enable/Disable
[Enable]
Automatic Off Time
[30s]
Brightness
[2]
Cancel
OK
When the [OK] is touched, the display returns to the
"Backlight Setting" screen.
NOTE
When set to "Disable", [Automatic Off Time] and
[Brightness] setting are unnecessary.
set) Go to (8).
Set the time until backlight is turned off .
(4) Touch the [Automatic Off Time] on the "Backlight Set-
ting" screen.
(5) "Automatic Off Time" screen is displayed. Select the [60
sec.] or [30 sec.].
(4)
Backlight Setting
Enable/Disable
[Enable]
Automatic Off Time
[30s]
Brightness
[2]
Cancel
OK
When the [OK] is touched, the display returns to the
"Backlight Setting" screen.
Adjust the brightness of Backlight
(6) Touch the [Brightness] on the "Backlight Setting" screen.
(7) "Brightness" screen is displayed. Adjust the brightness
with the [ ] or [ ].
(6)
Backlight Setting
Enable/Disable
[Enable]
Automatic Off Time
[30s]
Brightness
[2]
Cancel
OK
When the [OK] is touched, the display returns to the
"Backlight Setting" screen.
Apply the setting.
(8) After setting is complete,
touch the [OK] on the "Back-
light Setting" screen.
After the setting change is
displayed, the display returns
to the "Preference" screen.
Preference
Panel
Backlight
Calibration
Setting
Contrast
Back
(3)
Enable/Disable
Enable
Disable
Cancel
OK
(Cannot be
(5)
Automatic Off Time
60s
30s
Cancel
OK
(7)
Brightness
Brightness
3
2
1
Cancel
Cancel
OK
OK
Backlight Setting
Enable/Disable
[Enable]
Automatic Off Time
[30s]
Brightness
[2]
Cancel
OK
3-8-3 Contrast Setting
(1) Touch the [Contrast Setting] on the "Preference" screen.
(2) "Contrast Setting" screen is displayed. Adjust the con-
trast with [ ] or [ ].
(1)
Preference
Panel
Backlight
Calibration
Setting
Contrast
Back
When the [OK] is touched, after the setting change
screen is displayed, the display returns to the "Prefer-
ence" screen.
3-9 Initial Setting (for administrator)
Perform this setting at installation. The setting can also be
changed after installation.
(1) Touch the [Initial Setting] on the "Main Menu" screen.
(2) When "Password Verifi cation" screen is displayed, enter
the Password (or Installer Password) and touch [OK].
(1)
Main Menu
Page 2/ 3
Summer Time
Special Setting
Setting
Preference
Initial Setting
Previous
Next
Monitor
Page
Page
(3) If the password is entered correctly, the "Initial Setting"
screen is displayed. The screen has 3 pages which are
switched by touching the [Next Page] or [Previous Page].
Initial Setting
Page 1/ 3
Temp. Unit
Date Setting
Setting
R.C.Group
R.C. Sensor
Name Setting
Setting
Next
Back
Page
Initial Setting
Page 3/ 3
I.U. Display
Zone Setting
Number Setting
Previous
Back
Page
The following contents are set. (♦: for installer)
(*1: Items that indoor unit does not support are not dis-
played.)
(*2: Items are not displayed, if not connected to the zone
interface.)
• Date Setting:
The date and time display format are set. When the
power is turned off , the date and time data hold time
by built-in battery is approximately 7 days. When the
power is turned off for longer than this, the date and
time must be reset.
• Temp. Unit Setting:
The temperature display unit is switched to "°C" or "°F".
Factory settings is "°C".
• R.C.Group Name Setting:
The remote controller group name can be set or
changed.
(2)
Contrast
5
4
3
2
1
Cancel
OK
(2)
Password Verification
Enter Current Password
0
1
2
3
4
CL
5
6
7
8
9
Cancel
OK
Initial Setting
Page 2/ 3
Master Indoor
Password Setting
Unit Setting
Display Item
RC Master/
Setting
Slave Setting
Previous
Next
Back
Page
Page
En-18
Advertisement
Table of Contents
