Panel Mounting - DSC TL280LE-LAT Instruction Manual

LTE B3 1710 – 1785 MHz
1710 – 1755 MHz
LTE B4
824 – 849 MHz
LTE B5
LTE B7 2500 – 2570 MHz
703 – 748 MHz
LTE B28
WCDMA B1 1920 - 1980 MHz
WCDMA B2 1850 – 1910 MHz
WCDMA B4 1710 – 1755 MHz
WCDMA B5 824 – 849 MHz
2G B2 1850 – 1910 MHz
2G B3 1710 – 1785 MHz
2G B5 824 – 849 MHz
2G B8 880 - 915 MHz
References to model names TL280 (R) E , TL2803G (R) E, 3G2080 (R) E , TL280LE (R) and LE2080 (R) throughout this
manual apply to all specified models unless stated differently. Models ending in "R" include a built- in RS-232 interface for
connecting to local third-party applications.
3G2080(R)E: Is a HSPA (3G) cellular alarm communicator that sends alarm communication to Sur-Gard System I- IP, II, III
(SG-DRL3IP), IV (SG-DRL4IP), and 5 (SG-DRL5IP) central station receivers via a HSPA (3G)/GPRS digital cellular net-
work. TL2803G(R)E: Is a dual-path HSPA(3G) Ethernet alarm communicator that sends alarm communication to Sur- Gard
System -IPI, II, III, IV, and 5 central station receivers through Ethernet/Internet or a HSPA(3G)/GPRS digital cellular network.
TL280(R) E : Is an Ethernet alarm communicator that sends alarm communication to Sur- Gard System I- IP, II, III (SG-
DRL3IP), IV (SG-DRL4IP), and 5 (SG-DRL5IP) central station receivers via Ethernet/Internet.
LE2080(R): is an LTE (4G) cellular alarm communicator with HSPA(3G) fallback support that sends alarm communications
to Sur- Gard System I- IP, II, III (SG- DRL2IP, IV (SG-DRL4IP) and 5 (SG-DRL5IP) central station receivers via an LTE (4)
/HSPA(3G) digital cellular network.
TL280LER: Is a dual path LTE (4G) Ethernet alarm communicator that sends alarm communications to Sur-Gard System I-
IP, II, III (SG-DRL3IP, IV (SG-DRL4IP) and 5 (SG-DRL5IP) central station receivers via Ethernet/Internet or a LTE(4) /HSPA
(3G) digital cellular network.
The communicator can be used as either a backup or primary communicator. The communicator supports Internet Protocol
(IP) transmission of panel and communicator events over Ethernet/Internet and/or HSPA/GPRS.
The cellular performance of the LE2080(R), TL280LE(R), 3G2080(R) E or TL2803G(R) E communicators depend greatly
on the LTE(4G)/HSPA(3G) network coverage in the local area. A communicator placement test must be performed prior to
mounting the unit . A minimum of one green LED must be ON for good signal strength. Optional 3G/2G and LTE/3G
antenna extension kits are available to improve signal strength if required. GS-15ANTQ, GS- 25ANTQ and GS- 50ANTQ
kits are available for 3G/2G products and LTE- 15ANT, LTE-25ANT, LTE-50ANT extension kits are available for LTE/3G
products.
NOTE: Prior to installation, confirm with the local service provider that the network is available and active in the area where
the communicator will be installed, and that radio signal strength (CSQ) is adequate.
The following communicators are compatible with HS2016, HS2016-4, HS2032, HS2064, and HS2128 panels:
3G2080(R)E
(HSPA(3G)/GPRS only)
l
TL2803G(R)E
(Ethernet/Internet + HSPA(3G)/GPRS dual-path)
l
TL280(R)E
(Ethernet/Internet only)
l
LE2080(R) (LTE(4G)/HSPA(3G) only)
l
TL280LE(R) (Ethernet/Internet + LTE(4G)/HSPA(3G))
l
TL280LE-EU (Ethernet/Internet + LTE(4G)/HSPA(3G)/2G)
l
LE2080-EU (LTE(4G)/HSPA(3G)/2G only)
l
TL280LE-AU (Ethernet/Internet + LTE(4G)/HSPA(3G)
l
LE2080-AU LTE(4G)/HSPA(3G)
l
TL280LE-LAT(Ethernet/Internet + LTE(4G)/HSPA(3G)/2G)
l
LE2080-LATLTE(4G)/HSPA(3G)/2G
l
1805 – 1880 MHz
2110 – 2155 MHz
869 – 894 MHz
2620 – 2690 MHz
758 – 803 MHz
2110 - 2170 MHz
1930 – 1990 MHz
2110 – 2155 MHz
869 – 894 MHz
1930 – 1990 MHz
1805 – 1880 MHz
869 – 894 MHz
925 - 960 MHz

Panel Mounting

8