Table of Contents
Advertisement
10
iGO DRIVE
ADVANCED SETTINGS
use the PLUS (+) or MINUS (-) buttons to toggle through the list options.
Short press the POWER BUTTON to select the hi-lighted option.
use the PLUS (+) or MINUS (-) buttons to toggle through the selected option's values.
Short press the POWER BUTTON to confirm and save the hi-lighted value.
Advanced Settings
Power Set
0-9
Current Limit
22A
LCD Luminance
100%
Cruise Enable
ON
MODE
CLASS_3
Password
>
BACK
Power Set
Change the number of PAS levels used. 0-5 is the default value.
Selecting less levels of assist will deliver greater difference between each PAS level. Selecting
more assist levels will deliver a more gradual step up and down between each PAS levels.
Select from these values :
0-3
|
1-3
|
0-5
|
1-5
|
0-7
|
1-7
|
0-9
|
1-9
Note : If a value is selected that does not include '0' the eBike will start up in PAS '1'
i.e. touching the throttle at any time will cause the bike to move.
Take caution when using these values.
Current Limit
Value assigned to the controller 'over-current' cut setting. The default
value is 22A and should be the correct value for your bike. If you believe the
value or function is not working as expected contact iGO support.
LCD Luminance
Change the backlight brightness of the display unit (%).
Cruise Enable
ON or OFF.
Mode
iGO eBikes listed in this manual are MULTI CLASS SWITCHABLE through the display unit.
Select from the 'mode' values to reset the bike parameters and the eBike
will instantly conform to Class 1, Class 2, or Class 3 regulations.
Class_1 : No throttle function, PAS with maximum speed 32km/h (20mph)
Class_2 : Throttle and PAS maximum speed 32km/h (20mph)
Class_3 : Throttle maximum speed 32km/h (20mph), PAS maximum speed 45km/h (28mph)
To engage class 3 the rider can only operate where permitted by local regulations
and accept the liabilities and responsibilities of riding in this class.
ATTENTION : Riding an ebike in class 3 in an area prohibited by law is a punishable offence. It
is the riders responsibility to familiarize themselves regarding these regulations and further
agrees to hold iGO/Fermetco harmless or responsible in any way in the operation of their ebike.
Password
Select the '>' option to enter the password menu.
Password Set
BACK
Start Password
OFF
Select 'Start Password' and Short press the POWER BUTTON to proceed with
setting a password that will protect the electric functions of the eBike.
Password Set
Please Input Your
Password
-
- - -
A prompt will appear to enter a 4 digit password. Use the PLUS (+)
or MINUS (-) buttons to toggle through numbers and Short press the
POWER BUTTON to confirm and proceed to the next number.
Once all four numbers have been entered a prompt will appear to confirm the
password. Re-enter the 4 digit password to proceed. If the passwords do not
match an alert will be shown and the confirmation will need to be reentered.
A confirmation screen will show to indicate the password requirement has been set.
When active, the password can be reset (change the password) or set to OFF. Each of
these options will require entering the current password before being able to proceed.
Password Set
BACK
Start Password
ON
Reset Password
Note : the display will be powered off automatically if an incorrect password is entered ten
times.
When active, the 4 digit code will be required every time the display unit is powered on,
before the eBike electrical system can become operational. A password prompt will show
at start up and allows up to three attempts to input the correct numbers. The correct code
must be entered to access the electrical system controls and cyclocomputer interface.
PLEASE TAKE CARE TO REMEMBER YOUR PASSWORD AND ENSURE THE PASSWORD IS KEPT SAFE.
Back
Return to the previous menu.
11
Advertisement
Table of Contents
