Kraus Ramus GVR-204-RE Installation Manual
Single lever vessel faucet
Hide thumbs
Also See for Ramus GVR-204-RE:
- Installation manual (12 pages) ,
- Installation manual (12 pages)
Related Manuals for Kraus Ramus GVR-204-RE
Summary of Contents for Kraus Ramus GVR-204-RE
- Page 1 INSTALLATION MANUAL Ramus Single Lever Vessel Faucet FVS-1007 www.kraususa.com Toll Free: 1.800.775.0703 © 2018 Kraus USA Inc. REV. September 17, 2020...
- Page 2 Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com...
-
Page 3: Prior To Installation
Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. - Page 4 Diagram and Parts List Faucet Body Aerator Faucet Base A. Base Trim Ring B. Rubber Washer Mounting Hardware A. Rubber Washer B. Metal Washer C. Mounting Nuts D. Mounting Screws Hex Wrench Aerator Key...
-
Page 5: Faucet Dimensions
Faucet Dimensions 6 5/8" (168mm) 3 3/4" (96mm) 20° 5 3/4" Ø 1 3/4" (146mm) (45mm) 1 3/8" (35mm) Ø 2" (50mm) 3/8" Compression Installer Tip: Shut off main water supply before installing new faucet. - Page 6 Faucet Installation Procedure Step 1. Remove rubber washer (4A), metal washer (4B), mounting nut (4C), and mounting screws (4D). Keep the base trim ring (3A) and rubber washer (3B) on the base of the faucet. Step 2. Install the faucet through the 1-3/8"...
- Page 7 Step 3. Install flex water supply lines on the angle stops and tighten with an adjustable wrench. Turn on both the cold and hot main valves Apply pipe tape (optional). Step 4. After installing the faucet, remove the aerator (2) with the included aerator key (6).
-
Page 8: Replacement Parts
Replacement Parts Replacement Parts List Finish/Color Part # 1. Metal Handle CH, SN, ORB, MB, SFS* KP44069 2. Cartridge Cover CH, SN, ORB, MB, SFS* KP44070 3. Locking Nut KP44071 4. Cartridge KP44072 5. Aerator KP44073 CH, SN, ORB, MB, SFS* KP44074 6. -
Page 9: Troubleshooting
Trouble-Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Adjusting locking nut has come loose. Remove handle index button. Loosen set Leakage under the faucet screw with hex wrench. - Page 10 Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be repaired or replaced with a product of equal value at the option of Kraus. This warranty extends to the original owner or end-user, and is not transferable to a subsequent owner.
- Page 11 This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. KRAUS USA has the right to change, modify, and/or update the warranty policy at any time. For the latest, most up to date comprehensive warranty, go to www.kraususa.com/warranty...
- Page 12 IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.com...
- Page 13 INSTALLATION MANUAL Glass Vessel Sinks www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV. September 2, 2020...
- Page 14 Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com...
- Page 15 Toll-Free: 800-775-0703 or customerservice@kraususa.com The step-by-step guidelines in the installation instructions are a general reference for installing a Kraus sink. Should there be any discrepancies, Kraus cannot be held liable. It is recommended to install all Kraus products by hiring a licensed professional.
- Page 16 Dimensions Ø 16 1/2" Ø 14" (419mm) (356mm) Ø 1 3/4" Ø 1 3/4" (45mm) (45mm) Model #: GV-101-14, GV-101FR-14, Model #: GV-100, GV-101, GV-101FR, GV-103-14, GV-104-14 GV-104, GV-200, GV-204, GV-580, Sink Dimensions: Ø 14” x 5 1/2” GV-651, GV-684 Sink Dimensions: Ø...
- Page 17 Dimensions 16 1/2" (419mm) 21 7/8" (556mm) Ø 1 3/4" Ø 1 3/4" (45mm) (45mm) Model #: GVR-204-RE, GVR-210-RE Model #: GVS-901-19mm Sink Dimensions: 21 7/8” x 13 7/8" x 4” Sink Dimensions: 16 1/2” x 16 1/2" x 6” Glass Thickness: 15mm Glass Thickness: 19mm...
-
Page 18: Rough-In Dimensions
Rough-In Dimensions Finished Wall Ø 1 3/4” Drain Hole Top View 14” - 17” Countertop Mounting Ring 1/2” Floor Installer Tip Shut off main water supply before installation. -
Page 19: Before You Begin
Above Counter Installation Instructions Before You Begin Prepare counter top by drilling a 1 3/4’’ diameter drain hole at the desired location. Install mounting ring. Place vessel sink on the mounting ring or counter top as shown below. Make sure the vessel sink is not scratched, chipped or broken prior to installation. Check to see if your set contains the following parts: ·... - Page 20 Pop Up Drain & Mounting Ring Installation (Only if Included) Locate and disassemble your pop up drain in the following order: · Unscrew the tail piece Unscrew the brass nut · Remove the firm washer · Remove the concave washer, leaving the top thin rubber washer on. ·...
- Page 21 From above the countertop, insert the drain body into the 1 3/4” drain opening of your sink. From underneath the countertop, insert the concave white rubber washer onto the drain. Pushing the washer all the way up until it is in contact with the countertop. Insert the firm washer onto the drain body until it comes into contact with the concave white rubber washer.
- Page 22 Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be repaired or replaced with a product of equal value at the option of Kraus. This warranty extends to the original owner or end-user, and is not transferable to a subsequent owner.
- Page 23 Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com If you are a plumbing contractor or trade professional please contact a Kraus Pro Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.com...
- Page 24 IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.com...
- Page 25 Proservice@kraususa.com delay, property damage, or other consequential "Bathroom Accessories" in their original you for your business with Kraus USA. It is our damages, and Kraus accepts no liability for such location. The warranty is non-transferable. sincere hope that you are completely satisfied If you are an Authorized Partner please contact damages.
- Page 26 DIMENSIONS STEP 2 STEP 4 PU-10 DIAGRAM AND PARTS LISTS Install drain body (a), with rubber washer (b) Connect tailpipe (g) to p-trap. PU-L10 Ø 2 5/8" attached, into the drain hole. From underneath, (66.5mm) attach concave washer (c) (narrow end up), plastic washer (d) and mounting nut (e) to drain Ø...
Need help?
Do you have a question about the Ramus GVR-204-RE and is the answer not in the manual?
Questions and answers