Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for 4IPNET OWL530 v1.00
Summary of Contents for 4IPNET OWL530 v1.00
- Page 1 OWL530 v1.00 Outdoor Access Point/Bridge/CPE...
-
Page 2: Copyright Notice
Copyright Notice This document is protected by USA copyright laws and other laws. Besides, the document is the property of 4IPNET, INC. You may not copy, reproduce, distribute, publish, display, perform, or modify any part of this publication in any form or by any means without prior written permission from 4IPNET, INC. - Page 3 This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Copyright © 4IPNET, INC. All rights reserved.
- Page 4 This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported by 4ipnet Inc. may result in the equipment no longer being compliant with the regulatory requirements.
- Page 5 Quick Installation Guide OWL530 Outdoor AP/Bridge/CPE ENGLISH Preface Package Contents 1. 4ipnet OWL530 x 1 The 802.11 n/a/b/g compliant OWL530 is an 2. Ground Cable x 1 Outdoor AP/Bridge/CPE device that can be used for 3. Quick Installation Guide (QIG) x 1 multiple purposes.
-
Page 6: System Overview
Quick Installation Guide OWL530 Outdoor AP/Bridge/CPE ENGLISH System Overview OWL530 Ventilation Valve Due to extreme weather conditions, water vapor in the OWL530 may condense. The valve allows ventilation to prevent moisture buildup within the OWL530. Ground Connector For connecting the ground wire. PoE Connector For connecting to the Power Sourcing Equipment (PSE). -
Page 7: Hardware Installation
Quick Installation Guide OWL530 Outdoor AP/Bridge/CPE ENGLISH Hardware Installation OWL530 The following diagram is a basic network topology which can be used for testing and configuring the OWL530. Installation Steps: Step 1. Connect two N-type antennas to the N-type connectors Step 2. - Page 8 Quick Installation Guide OWL530 Outdoor AP/Bridge/CPE ENGLISH Insert the RJ45 cable through the outer opening of cap (C) Insert the RJ45 connector and wrap (A) around the Ethernet cable through the slit between the connector and cap (C) Wrap (B) around (A) through the slit on (B) - 4 -...
- Page 9 Quick Installation Guide OWL530 Outdoor AP/Bridge/CPE ENGLISH Insert Parts (A) and (B) together into the PoE Port Screw cap (C) onto the PoE Port Step 3. Connect one end of another Ethernet cable to the PSE (Data Link) and the other end to a computer. Step 4.
- Page 10 Quick Installation Guide OWL530 Outdoor AP/Bridge/CPE ENGLISH Step 2. Align the front of OWL530 with the pole and insert the U-shaped bolts into the 4 holes on the corners of the OWL530. Step 3. Secure the OWL530 by screwing on the nuts after the inserting the washers for all four corners. - 6 -...
-
Page 11: Getting Started
Outdoor AP/Bridge/CPE ENGLISH Getting Started 4ipnet OWL530 supports web-based configuration. OWL530 is a dual-mode system where AP Mode is the default mode, can be configured as either an access point (AP Mode) or a gateway (CPE Mode) based on your deployment needs. It is required to follow the respective installation procedures provided to properly set up the desired mode for this system. - Page 12 System Login The system manager Login Page will then appear. Enter “admin” in the User name field and “admin” in the Password field, and then click Login to log in. - 8 - Copyright © 4IPNET, INC. All rights reserved.
- Page 13 To logout, simply click on the Logout button at the upper right hand corner of the interface. AP mode is the default mode. The administrator must access the system via the AP Note: mode login page first before switching modes. - 9 - Copyright © 4IPNET, INC. All rights reserved.
-
Page 14: Common Settings
Ensure the Operating Mode is currently in AP mode. Click on the Status button and then select the System Overview tab. The Operating Mode is at the System section on the System Overview page. - 10 - Copyright © 4IPNET, INC. All rights reserved. - Page 15 Click on the Utilities button and then select the Password tab. Enter a new password in the New Password field and retype it in the Re-enter New Password field. Click SAVE to save the changes. - 11 - Copyright © 4IPNET, INC. All rights reserved.
- Page 16 Click on the System button and then select the Network Interface tab. Click the Static radio button and enter the related information in the fields marked with red asterisks. Click SAVE to save the settings. - 12 - Copyright © 4IPNET, INC. All rights reserved.
- Page 17 ESSID: Enter respective ESSID for each VAP in the ESSID field or use the default. ESSID (Extended Service Set Identifier) is a unique identifier used for networking devices to get associated with OWL530. Click SAVE to save the settings. - 13 - Copyright © 4IPNET, INC. All rights reserved.
- Page 18 Enter the information required in the blank fields. Click SAVE to save all settings configured so far; all updated settings will take effect upon reboot. Congratulations! AP mode is now successfully configured. - 14 - Copyright © 4IPNET, INC. All rights reserved.
- Page 19 Ensure the Operating Mode is currently in CPE mode. Click on the Status button and then select the System Overview tab. The Operating Mode is at the System section on the System Overview page. - 15 - Copyright © 4IPNET, INC. All rights reserved.
- Page 20 Change Admin Account Password Enter a new password in the New Password field and retype it in the Re-enter New Password field. Click SAVE to save the changes. - 16 - Copyright © 4IPNET, INC. All rights reserved.
- Page 21 Select AP to be Associated Select an AP to be associated with from the Scan Result list provided in Step 3. Click Connect to connect to an SSID without Security Settings. - 17 - Copyright © 4IPNET, INC. All rights reserved.
- Page 22 Enter the information required in the configuration box. Information to be entered must be exactly the same as configured in this selected AP. Click Connect to start the connection. - 18 - Copyright © 4IPNET, INC. All rights reserved.
- Page 23 【Settings here are for example only】 Click on the System button and then select Network tab. Enable Static, and then enter the related information in the fields marked with red asterisks. - 19 - Copyright © 4IPNET, INC. All rights reserved.
- Page 24 It is strongly recommended to make a backup copy of configuration settings. For further configuration and backup information, please refer to the User’s Manual. P/N: V10020140918 - 20 - Copyright © 4IPNET, INC. All rights reserved.