Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for 4IPNET OWL630
Summary of Contents for 4IPNET OWL630
- Page 1 OWL630 V1.00 Outdoor Access Point...
-
Page 2: Copyright Notice
4IPNET, INC. You may not alter or remove any copyright or other notice from copies of the content. All other brand and product names are claimed or registered marks of their respective companies or organizations. - Page 3 This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Copyright © 4IPNET, INC. All rights reserved.
- Page 4 This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported by 4ipnet Inc. may result in the equipment no longer being compliant with the regulatory requirements.
- Page 5 ENGLISH Preface Package Contents 1. 4ipnet OWL630 x 1 The OWL630 is a rugged multi-mode, high-end dual 2. Quick Installation Guide (QIG) x 1 radio 802.11 b/g/n + ac MIMO Access Point (AP), 3. Power Sourcing Equipment (PSE) X 1...
-
Page 6: System Overview
Connector marked –1 is for the primary antenna when the AP is not in 802.11n or 802.11ac mode. Utilize all connectors for optimized MIMO performance. Back Ground Connector For connecting the ground wire Copyright © 4IPNET, INC. All rights reserved. - Page 7 Bottom M12 DC Connector DC input (12V) is supported on OWL630 Ventilation Valve Due to extreme weather conditions, water vapor in the OWL630 may condense. The valve allows ventilation to prevent moisture buildup within the OWL630. Uplink (PoE Connector) For connecting to the Power Sourcing Equipment (PSE)
-
Page 8: Hardware Installation
Quick Installation Guide OWL630 Enterprise Access Point ENGLISH Hardware Installation The following are the basic installation steps which can be used for testing and configuring the OWL630. Installation Steps: Step 1. Connect an antenna to the connector. Step 2. Connect the Ethernet Port of OWL630 to the POWER & DATA OUT Port of the PSE. - Page 9 Step 4. Plug the RJ-45 Connector into the system and make sure the locking ring is locked in well. Step 5. Coil waterproof tape to secure the parts of the Waterproof Connector Pack. Copyright © 4IPNET, INC. All rights reserved.
- Page 10 The M12 Waterproof Connector Pack is used for DC power supply, and it consists of 5 parts: Step 1. Pass power cable through the Sealing Nut, Gaskets, and Clamp Ring (items 2-5) Step 2. Solder power pins with reference to the pin definition below Pin Number Pin Definition V– Copyright © 4IPNET, INC. All rights reserved.
- Page 11 OWL630 Enterprise Access Point ENGLISH Step 3. Seal all connectors and fasten sealing nuts Now, the Hardware Installation is complete. For installation instruction on mounting, please refer to the Outdoor Installation Guide (4ipnet_TEC_Outdoor_Installation_Guide_R2_20140220.pdf). Copyright © 4IPNET, INC. All rights reserved.
-
Page 12: Getting Started
1. To access the web management interface, connect the administrator PC to the LAN port of OWL630 via an Ethernet cable. Then, set a static IP address on the same subnet mask as OWL630 in TCP/IP of your PC, such as the following example: IP Address: 192.168.1.100... - Page 13 OWL630 Enterprise Access Point ENGLISH Administrator Login Page 4. After a successful login into OWL630’s Web user interface (Web UI), a System Overview page of web management interface will appear, as depicted below. The Web Management Interface - System Overview Page 5.
-
Page 14: Common Settings
Enter the old password and then a new password with a length of up to 32 characters, and retype it in the Re-enter New Password field. Click SAVE to save the changes. Copyright © 4IPNET, INC. All rights reserved. - Page 15 802.11g+802.11n for the band and 1 for the channel. Admin should be aware of Dynamic Frequency Selection (DFS) mandated on some channels of the 5GHz band. When OWL630 detects interference, this mechanism will limit the ability to broadcast the SSID on one of the channels listed below: ...
- Page 16 Step 3. Configure VAP (Virtual Access Point) Profile Settings VAP Configuration Page (VAP-1 shown) OWL630 supports up to 16 virtual APs per RF card (VAPs). Configure VAP profile settings： (a) Select the VAP Configuration tab to configure the settings of the desired VAP.
- Page 17 Quick Installation Guide OWL630 Enterprise Access Point ENGLISH Virtual AP Overview Page Copyright © 4IPNET, INC. All rights reserved.
- Page 18 ENGLISH Step 4. Configure WDS (Wireless Distribution System) Settings (Optional) To extend the wireless coverage, OWL630 supports up to 8 WDS links for connecting wirelessly to other WDS-capable APs (peer APs). By default, all WDS profiles are disabled. Click on the Wireless main menu button.
- Page 19 OWL630 Enterprise Access Point ENGLISH After OWL630's network configuration is completed, please remember to change the IP Address of your PC Connection Properties back to its original settings in order to ensure that your PC functions properly in its real network environments.