Sabbath Mode; Basic Settings - Bosch HRG4785 1 Series User Manual And Installation Instructiions

Table of Contents

Advertisement

15  Basic settings
You can configure the basic settings for your appliance to meet your needs.
15.1 Overview of the basic settings
Here you can find an overview of the basic settings and factory settings. The basic settings depend on the features
of your appliance.
Display
Basic setting
​ ⁠ ​ ⁠ ​ ⁠
Signal duration upon completion of a time or
timer period
​ ⁠ ​ ⁠ ​ ⁠
Waiting time until a setting is applied
​ ⁠ ​ ⁠ ​ ⁠
Button tone when pressing a button
​ ⁠ ​ ⁠ ​ ⁠
Brightness of the display illumination
​ ⁠ ​ ⁠ ​ ⁠
Time display
​ ⁠ ​ ⁠ ​ ⁠
Childproof lock can be adjusted
→ "Childproof lock", Page 20
​ ⁠ ​ ⁠ ​ ⁠
Interior lighting during operation
​ ⁠ ​ ⁠ ​ ⁠
Cooling fan run-on time
​ ⁠ ​ ⁠ ​ ⁠
Telescopic shelves retrofitted
​ ⁠ ​ ⁠ ​ ⁠
Sabbath mode available
→ "Sabbath mode", Page 20
​ ⁠ ​ ⁠ ​ ⁠
Water hardness
→ "Setting the water hardness", Page 22
​ ⁠ ​ ⁠ ​ ⁠
Automatic rapid heating from 200 °C
​ ⁠ ​ ⁠ ​ ⁠
Reset all values to factory settings
1
Factory setting (may vary according to model)
Depending on the appliance specifications
2
15.2 Changing basic settings
Requirement: The appliance is switched off.
Press and hold the
1.
four seconds.
a The first basic setting appears in the display,
e.g.  ​ ⁠ ​ ⁠ ​ ⁠   ​ ⁠ .
Use the temperature selector to change the setting.
2.
Use the
​ ⁠ or
​ ⁠   button to switch to the next basic
3.
setting.
To save the changes, press and hold the
4.
for approx. four seconds.
2
​ ⁠   button for approximately
​ ⁠   button
Selection
​ ⁠ = 10 seconds
​ ⁠ = 30 seconds
​ ⁠ = 2 minutes
​ ⁠ = 3 seconds
​ ⁠ = 6 seconds
​ ⁠ = 10 seconds
​ ⁠ = off
1
​ ⁠ = on
​ ⁠ = dark
1
​ ⁠ = medium
​ ⁠ = bright
​ ⁠ = hide the time
​ ⁠ = display the time
​ ⁠ = no
1
​ ⁠ = yes
​ ⁠ = yes, with locked door
​ ⁠ = no
1
​ ⁠ = yes
​ ⁠ = short
1
​ ⁠ = medium
​ ⁠ = long
​ ⁠ = extra-long
1
​ ⁠ = no
(for rails and 1-level pull-out)
​ ⁠ = yes (for 2- and 3-level pull-out)
1
​ ⁠ = no
​ ⁠ = yes
​ ⁠ = softened
​ ⁠ = soft (up to 1.5 mmol/l)
​ ⁠ = medium (1.5–2.5 mmol/l)
​ ⁠ = hard (2.5–3.8 mmol/l)
​ ⁠ = very hard (above 3.8 mmol/l)
2
​ ⁠ = no
1
​ ⁠ = yes
1
​ ⁠ = no
​ ⁠ = yes
Note: Your changes to the basic settings will be re-
tained even after a power failure.
15.3 Discarding changes to the basic
settings
Turn the function selector.
a All changes are discarded and not saved.
1
1
1
1
Basic settings en
21

Advertisement

Table of Contents
loading

Table of Contents