Ibm personal computer - desktop pc user manual (64 pages)
Summary of Contents for IBM Anyplace Kiosk 4836
Page 1
All manuals and user guides at all-guides.com Anyplace Kiosk 4836 Planning, Installation and Service Guide GA27-4347-00...
Page 2
All manuals and user guides at all-guides.com...
Page 3
All manuals and user guides at all-guides.com Anyplace Kiosk 4836 Planning, Installation and Service Guide GA27-4347-00...
Page 4
PO Box 12195 Research Triangle Park, North Carolina, 27709 U.S.A. When you send information to IBM, you grant IBM a nonexclusive right to use or distribute whatever information you supply in any way it believes appropriate without incurring any obligation to you.
Appendix C, “Notices” provides legal, emission, and country-specific information. v Appendix D, “Safety information” provides safety information for all common languages. Throughout this guide, the term 4836 and IBM 4836 refer to the IBM Anyplace Kiosk. Who should read this guide Personnel responsible for installing, maintaining, and using the IBM Anyplace Kiosk should read this guide.
End of life disposal IBM encourages owners of information technology (IT) equipment to responsibly recycle their equipment when it is no longer needed. IBM offers a variety of programs and services to assist equipment owners in recycling their IT products.
Page 16
All manuals and user guides at all-guides.com Anyplace Kiosk 4836...
All manuals and user guides at all-guides.com Chapter 1. Introducing the IBM Anyplace Kiosk The IBM Anyplace Kiosk (see Figure 1) is a comprehensive and compact, touch screen terminal for self-service applications. The rugged aspect of the 4836 makes the product suitable for a wide variety of uses, such as retrieving information, listening to music, or watching multi-media presentations.
Table 2 describes some of the common 4836 models. Administrative models and other models that represent different service repair options are not listed. See your IBM representative for a complete list. Note: These models do not include the HDD, scanner, or MSR.
This mount is compatible with any third-party mount with 75 x 75 mm or 100 x 100 mm mounting holes. System software, touch drivers, and diagnostics The IBM Anyplace Kiosk supports all standard PC-function drivers and provides interfaces for the following I/O: Touch screen...
All manuals and user guides at all-guides.com You can obtain the appropriate software for your Anyplace Kiosk from the IBM Retail Store Solutions Web site: www.ibm.com/solutions/retail/store/ (from the store page, click on Support). Supported operating systems The IBM Anyplace Kiosk supports these operating systems: ™...
Input voltage and current 100–240 V 50–60 Hz 1.4A max: Input to power supply Calling for service When you call IBM for warranty information or service, be sure to have the following information available: v Machine type/model v Serial number You can locate this information on the lower-left edge at the rear of the machine.
Page 22
All manuals and user guides at all-guides.com Anyplace Kiosk 4836...
Installing the control button cover ....16 This section describes procedures for setting up the Anyplace Kiosk product. You should be familiar with the rear doors and connectors of the IBM 4836 before you begin the installation steps.
All manuals and user guides at all-guides.com Rear view and connectors Figure 2 shows the rear view of the IBM 4836. Figure 2. Rear view showing access doors, mounting holes, attachment holes Hard drive door Memory door Cable cover USB cover Holes that allow for the following standard mounting screws: v 100 mm x 100 mm (3.93 in.
Be sure to route the cables through the mounting stand before connecting to the unit. 3. Install the IBM 4836 on your mounting option: table top (see “Table-top mount” on page 15) or wall (see “Wall mount” on page 15 or the third-party mount instructions).
Figure 4). Installing the options The design of the IBM 4836 allows you to install the hard drive, scanner and MSR without removing the external cover. Many upgrade features are factory-installed. See Figure 2 on page 8 to identify the access doors.
All manuals and user guides at all-guides.com Installing the scanner 1. As shown in Figure 5, place the IBM 4836 face down on a sturdy surface. Figure 5. Installing the scanner 2. Lift the cable covers as described in “Opening the cable covers” on page 9.
A in Figure 7 shows the grounding strap, which is folded for the 12 inch Note: unit, unfolded for the 15 inch unit. 6. Install the hard drive door with MSR latching tab and secure the two screws. Anyplace Kiosk 4836...
See Figure 2 on page 8 to identify the hard drive access door. Figure 8. Removing the hard drive cover 1. Place the IBM 4836 face down on a sturdy surface. 2. Unfasten the two captured screws to remove the HDD door ( A ) . See Figure 8.
4. Rotate the outer edge of the memory card downward until it snaps into place. Note: You must remove the back cover if you are replacing both memory modules. Mounting instructions You can choose between a table-top, wall mount, or a third party mount. Anyplace Kiosk 4836...
5. Attach the mount to the unit with the four screws. 6. Install the base cover ( A ) and the arm cover ( B ). 7. Place the IBM 4836 unit in the desired location and retain the cables (see “Retaining the cables” on page 10).
Powering on Notes: 1. Your new IBM 4836 ships with a control cover. If you want the buttons covered, install this part after you power on and adjust the image. 2. A small hole ( E in Figure 11) under the control cover allows you access to the reset switch.
AC power outlet. The method of mounting must be able to support the combined weight of the IBM 4836 plus the suspended weight of all the cables to be attached to the system. Use the following methods for mounting...
Additionally, you should adjust the display’s initial angle of tilt to provide adequate and comfortable viewing by the users for the tasks that they perform. Figure 13. IBM 4836 mounting height Anyplace Kiosk 4836...
Note: Wall mount plate is not drawn to scale. 98 mm (3.87 in) Cable Exit 60 mm 18 mm (2.37 in) (0.75 in) Figure 14. Wall mount plate dimensions Chapter 3. Mounting the IBM Anyplace Kiosk to the wall...
Page 36
If the recommended size is not available, choose the next longer or larger size. Choose fasteners that are rated either ”Medium Duty“ or ”Heavy Duty.“ To assure proper fastener selection and installation, follow the fastener manufacturer’s recommendations. Anyplace Kiosk 4836...
Page 37
After installation, make sure that the screw heads are flush or below the outer surface of the wall mount plate. Check to make sure that you firmly and securely attach the wall mount plate to the wall. Chapter 3. Mounting the IBM Anyplace Kiosk to the wall...
Page 38
See Table 9 on page 24 for additional descriptions. After installation, make sure the screw heads are flush or below the outer surface of the wall mount plate. Check to make sure you firmly and securely attach the wall mount plate to the wall. Anyplace Kiosk 4836...
Page 39
After installation, make sure that the screw heads are flush or below the outer surface of the wall mount plate. Check to make sure that you attached the wall mount plate firmly and securely to the wall. Chapter 3. Mounting the IBM Anyplace Kiosk to the wall...
Cobra WallDriller Note: Metal casing size is dependent on wall board thickness. During installation, grip head of metal casing with pliers when initially tightening the screw to flare the legs. ”No drill“ or ”drive“ types are not recommended. Anyplace Kiosk 4836...
Page 41
Self-Drilling Drywall Toggle Bolt Lag screw Screw size: #8 or 4-mm nominal Screw size: 6.3 mm (1/4-in.) or thread diameter nominal thread diameter Length: 2.5 in. or 60 mm minimum Chapter 3. Mounting the IBM Anyplace Kiosk to the wall...
Page 42
All manuals and user guides at all-guides.com Anyplace Kiosk 4836...
Note: Procedures in this section should be performed by qualified service personnel. Reviewing the IBM 4836 assembly Figure 15 on page 28 summarizes the field replaceable parts of the IBM 4836 assembly. The part number associated with each FRU is located in Appendix A, “Field-replaceable units.”...
3. Place the unit on a sturdy surface. Removing the back cover Follow these steps to remove the back cover: 1. Place the IBM 4836 face down on a sturdy surface. 2. If installed, remove the MSR and scanner. Anyplace Kiosk 4836...
All manuals and user guides at all-guides.com 3. If installed, remove the button cover by prying under one end with a small screwdriver. 4. Locate and unfasten the five captured screws (see Figure 16) securing the back cover. Figure 16. Removing the back covers 5.
2. See Figure 17 and locate the main shield ( B ) that is attached to the back cover ( C ). 3. Remove the three screws ( A ) holding the shield and lift to remove. 4. To replace, reverse these procedures. Anyplace Kiosk 4836...
All manuals and user guides at all-guides.com Removing the wireless card Follow these steps to remove the wireless card: Note: You do not have to remove the back cover to remove the wireless card. 1. Place the 4836 face down on a sturdy surface. Figure 18.
2. Locate the blue CMOS jumper on the main planar assembly. See Figure 19. The jumper is located near the hard drive and beside the radio card. 3. Remove the jumper from the board and wait several seconds. 4. Reinstall jumper to reset defaults. Anyplace Kiosk 4836...
All manuals and user guides at all-guides.com Removing the memory card To remove the optional memory card, reverse the steps listed in “Installing additional memory” on page 13. To remove the factory-installed memory, follow these steps: 1. Remove the back cover as described in “Removing the back cover” on page 28. 2.
2. Locate the battery on the main planar assembly ( B in Figure 21). 3. Using your finger, press on one of the tabs holding the battery coin and the battery pops out. 4. To replace the battery, align the battery underneath the tabs and press down. Anyplace Kiosk 4836...
All manuals and user guides at all-guides.com Removing the heat sink Attention: To avoid damage to the unit, establish personal grounding before touching this unit. To remove the heat sink and processor: Figure 22. Heat sink and processor 1. Unplug the fan connector, which is shown as C in Figure 20 on page 33. 2.
3. Remove the four screws ( C ) holding the hard disk drive bracket ( D ) and lift to remove. 4. To replace, locate the right and left side rails with the correct side of the rails upward. 5. Replace the 4 screws. 6. Reinstall the hard disk drive and door. Anyplace Kiosk 4836...
All manuals and user guides at all-guides.com Removing the speakers Follow these steps to remove the speakers: 1. Remove the back cover as described in “Removing the back cover” on page 28. 2. Detach each speaker cable ( A in Figure 24) from the adjacent circuit board. Figure 24.
5. Carefully lift to remove. 6. To replace, reverse these procedures noting to align the board with the three pins for the correct positioning. Note: Be sure the board is fully seated on the connectors along the top and sides. Anyplace Kiosk 4836...
All manuals and user guides at all-guides.com Removing the control card 1. Remove the back cover as described in “Removing the back cover” on page 28. Figure 26. Removing the control card 2. See Figure 26. Disconnect the control panel cable ( A ). 3.
6. Unfasten the three screws ( C ) to remove the card. 7. To replace, locate the alignment pin ( D ) and hole and lower the front panel card onto the pin. 8. Replace the three screws. Anyplace Kiosk 4836...
All manuals and user guides at all-guides.com Removing the backlight inverter card 1. Remove the back cover as described in “Removing the back cover” on page 28. 2. Disconnect and remove the hard drive fan as described in “Removing the hard drive fan”...
5. Turn the LCD assembly over to locate and remove the four screws holding the LCD to the back of the LCD assembly. Remove the LCD. 6. Disconnect the main signal cable from the back of the LCD. Anyplace Kiosk 4836...
All manuals and user guides at all-guides.com Figure 30. Replacing the LED assembly 7. To replace, see Figure 30 and follow these steps: a. Plug the signal cable to LCD. b. Place the assembly face up on a steady surface. c.
5. Remove the eight screws ( E ) holding the LCD assembly (includes the system board) to the front bezel. 6. Lift out the LCD assembly from the front bezel, being careful not to bend the antenna. 7. To replace the front bezel, reverse these procedures. Anyplace Kiosk 4836...
All manuals and user guides at all-guides.com Removing the mounting stand cover set To remove the cover set for the table-top mounting stand, follow these steps: Figure 32. Removing the stand cover set 1. Remove the arm cover ( B ) by pulling on the finger recess ( A in Figure 32) located on the top of the cover.
2. Unplug the cable connected to the volume control card. Figure 33. Removing the volume control card (Model 13V) 3. Remove the four screws holding the volume control card and lift out. 4. To replace, reverse these procedures. Anyplace Kiosk 4836...
Page 64
Replace the MSR. Table-top mount tilts too easily 1. Remove the arm cover and base top cover from the stand. 2. Tighten the two nuts at the joint until you obtain the desired friction. 3. Reinstall the covers. Anyplace Kiosk 4836...
All manuals and user guides at all-guides.com Assembly 1: (continued) Assembly 1: 4836 Models 132 and 13V - 12 inch Anyplace Kiosk 4836...
Page 67
All manuals and user guides at all-guides.com Assembly 1: (continued) Asm– Part Index Number Units Description 1–1 57P4174 Memory door –2 57P4182 Speaker (Model 132 only) – 57P4220 Cable-speaker extension (Model 132 only) –3 61P5704 Scanner assembly (option) –4 57P4211 Scanner window –...
All manuals and user guides at all-guides.com Assembly 2: 4836 Models 135 - 15 inch Anyplace Kiosk 4836...
Page 69
All manuals and user guides at all-guides.com Assembly 2: (continued) Asm– Part Index Number Units Description 2–1 57P4176 Memory door – 15 inch –2 57P4182 Speaker –3 61P5704 Scanner assembly (option) –4 57P4211 Scanner window – 57P4212 Scanner blank –5 57P4189 Processor –5...
All manuals and user guides at all-guides.com Assembly 3: Mounting — Table-top stand Anyplace Kiosk 4836...
Page 71
All manuals and user guides at all-guides.com Assembly 3: (continued) Asm– Part Index Number Units Description 3–1 57P4465 Table-top stand (with covers) –2 57P4210 Stand cover kit –3 57P4466 Wall mount Appendix A. Field-replaceable units...
Honduras, Jamaica, Mexico, Netherlands Antilles, Nicaragua, Panama, Peru, Philippines, Saudi Arabia, Taiwan, Thailand, US (except Chicago), Venezuela, 49P2102 Brazil 49P2058 India, Bangladesh, Pakistan, South Africa, Sri Lanka 75H8989 US — required in Chicago (1.8 M) 49P2068 Liechtenstein 49P2062 Denmark Anyplace Kiosk 4836...
All manuals and user guides at all-guides.com 15-inch models Note: Dimensions are shown in millimeters. Figure 35. Dimensions for 15-inch models Anyplace Kiosk 4836...
References in this publication to IBM products, programs, and services do not imply that IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM product, program, or service is not that only IBM’s product, program, or service may be used.
Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment.
In solch einem Fall ist der Abstand bzw. die Abschirmung zu der industriellen Störquelle zu vergröβern.″ Anmerkung: Um die Einhaltung des EMVG sicherzustellen, sind die Geräte, wie in den IBM Handbüchern angegeben, zu installieren und zu betreiben. Australia / New Zealand Attention: This is a Class A product.
The ESD ground clip can be attached to any frame ground, ground braid, green wire ground, or the round ground prong on the AC power plug. Coax or connector outside shells can also be used. Handling Removed Cards Anyplace Kiosk 4836...
Attach tags or reports that must accompany the card to the outside of the container. Regulatory notice for T60H786 IBM 11bg wireless LAN mini PCI adapter The IBM Wireless LAN Mini PCI Adapter must be installed and used in strict accordance with the following instructions. This product complies with the following radio frequency standards.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: 1. il ne doit pas produire de brouillage et 2. l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Anyplace Kiosk 4836...
Page 81
All manuals and user guides at all-guides.com Exposure of humans to RF fields (RSS-102) IBM Anyplace Kiosk 4836 computers employ low gain integral antennas that do not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s web site at www.hc-sc.gc.ca/rpb...
Page 82
All manuals and user guides at all-guides.com Anyplace Kiosk 4836...
Page 83
All manuals and user guides at all-guides.com Appendix C. Notices...
Page 84
All manuals and user guides at all-guides.com Notice for users in Korea Anyplace Kiosk 4836...
Page 85
All manuals and user guides at all-guides.com The wireless device may cause radio wave interference during operation. Notice for users in Singapore Operating conditions under which the radiocommunication equipment are exempted from licensing To maximize frequency sharing while minimizing radio interference, the following operating conditions are imposed to confine the propagation of radio signals within a building or at a localised site: v The radiocommunication equipment shall be used for in-building or localised...
All manuals and user guides at all-guides.com Trademarks IBM, the IBM logo, PS/2, SureMark and SurePoint are trademarks of IBM Corporation in the United States or other countries or both. Microsoft, Windows, Windows NT, and the Windows 95 logo are trademarks or registered trademarks of Microsoft Corporation.
All manuals and user guides at all-guides.com Appendix D. Safety information Danger: Before you begin to install this product, read the safety information in IBM Safety Information — Read This First, GA27-4004. This booklet describes safe procedures for cabling and plugging in electrical equipment.
Page 88
Gevaar Voordat u begint met het installeren van dit produkt, dient u eerst de veiligheidsrichtlijnen te lezen die zijn vermeld in de publikatie IBM Safety Information — Read This First, GA27-4004. In dit boekje vindt u veilige procedures voor het aansluiten van elektrische appratuur.
Page 89
All manuals and user guides at all-guides.com Vigyázat Mielôtt megkezdi a berendezés üzembe helyezését, olvassa el a IBM Safety Information — Read This First, GA27-4004 könyvecskében leírt biztonsági információkat. Ez a könyv leírja, milyen biztonsági intézkedéseket kell megtenni az elektromos berendezés huzalozásakor illetve csatlakoztatásakor.
Page 90
Varning—livsfara Innan du börjar installera den här produkten bör du läsa säkerhetsinformationen i dikumentet Säkerhetsföreskrifter—Läs detta först, GA27-4004. Där beskrivs hur du på ett säkert sätt ansluter elektrisk utrustning. Anyplace Kiosk 4836...
Page 91
All manuals and user guides at all-guides.com GA27-4004 GA27-4004 Appendix D. Safety information...
Page 92
All manuals and user guides at all-guides.com GA27-4004 GA27-4004 GA27-4004 GA27-4004 GA27-4004 GA27-4004 Anyplace Kiosk 4836...
Page 94
(1) Any part of a network other than an attaching device, such as an IBM 8228 Multistation diagnostics. Modules or tests used by computer users Access Unit. (2) Hardware or software that is part of a and service personnel to diagnose hardware problems.
Page 95
FCC. See Federal Communications Commission. Synonymous with fixed disk. feature. A part of an IBM product that may be ordered HID. See human interface devices. separately by the customer. hot pluggable. Refers to a hardware component that Federal Communications Commission (FCC).
Page 96
(3) In the IBM Store System, the logical link providing two-way communication of data from one network node to one or more other network nodes.
Page 97
Contrast with volatile priced for purchase by individuals or small businesses. memory. Examples include the various models of the IBM Personal Computers. NVRAM. See nonvolatile random access memory. plug. (1) A connector for attaching wires from a device to a cable, such as a store loop.
Page 98
(ROM), random access memory (RAM), and the I/O channel. It may have one or more disk or diskette drives. (3) In an IBM Store System terminal, the Anyplace Kiosk 4836...
Page 99
All manuals and user guides at all-guides.com part of the terminal that contains the processing unit, ROM, RAM, disk and diskette drives, and the I/O channel. terminal. In data communication, a device, usually equipped with a keyboard and a display, that is capable of sending and receiving information.
Page 100
All manuals and user guides at all-guides.com Anyplace Kiosk 4836...
Page 102
17 mounting stand cover set removal 45 retaining the cables 10 mounting system to a wall 17 reviewing the IBM 4836 assembly 27 mounting to hollow walls 21 MSR malfunctioning 48 MSR, installing 11 safety information 71...
Page 103
All manuals and user guides at all-guides.com unacceptable image quality 48 volume control card (Model 13V only) 46 wall mounting the system 17 wall mount plate attaching 20 determining the mounting height of 18 mounting options 19 selecting the location 18 walls, mounting to hollow 21 warranty information 5 wireless LAN 3...
Page 104
All manuals and user guides at all-guides.com Anyplace Kiosk 4836...
Page 105
Thank you for your responses. May we contact you? h Yes h No When you send comments to IBM, you grant IBM a nonexclusive right to use or distribute your comments in any way it believes appropriate without incurring any obligation to you. Name...
Page 106
All manuals and user guides at all-guides.com Readers’ Comments — We’d Like to Hear from You Cut or Fold Along Line GA27-4347-00 Fold and Tape Please do not staple Fold and Tape _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ NO POSTAGE NECESSARY IF MAILED IN THE...
Page 107
All manuals and user guides at all-guides.com...
Page 108
All manuals and user guides at all-guides.com Printed in USA GA27-4347-00...