Figure 1: Specifications Label Please have the assembly number, model number, and the date manufactured on hand when calling Daktronics customer service to ensure the request is serviced as quickly as possible. Knowing the facility name and/or job number will also be helpful.
Listed below are drawing types commonly used by Daktronics, along with the information typically provided. All drawings referenced in this manual are found in the appendices. Schematic Drawings: describe internal power and signal wiring as well as • interconnections between display sections; they may also include digit designations...
Ventilation and Temperature Requirements Daktronics pitch time displays are front ventilated. The display must NOT be fully enclosed inside a support structure or behind a face of plastic, glass, or other material. The front of the display must be exposed to the air to allow for convection cooling.
The Final Assembly drawings in Appendix A show details on access for electrical connections and the electrical requirements for that size of display. Daktronics display front panels are hinged to allow access to the digits, cabling, and other electronic components. See Access Internal Components (p�5) for cabinet access details.
Access Internal Components The doors of Daktronics pitch time displays are secured by slotted fasteners. 1� Release a fastener by gently turning it counter-clockwise with a flat-head screwdriver. 2� Open the doors using the knob attached to the display face (if provided) or by gently pushing the door outward from inside of the display (if there are no knobs).
– must be electrically grounded. Only qualified individuals may perform electrical work, including verification of ground resistance. Daktronics is not responsible for improper grounding or damage incurred as a result of improper grounding. Grounding methods must meet the provisions of all applicable local and national codes.
Connection CAUTION Power and signal cables are routed into the display from the rear (or sides) via separate conduits. All HAZARDOUS VOLTAGE power and signal wiring terminates at the fiber/ BEHIND THIS PANEL surge card enclosure. Note that systems with radio control typically only require signal wiring for backup Figure 6: Power Warning Label purposes.
(part # W-1242). This method requires a signal converter between the All Sport console’s scoreboard output and the fiber optic cable (not provided by Daktronics). To connect signal to nearby displays, route *copper* signal wire in conduit from SIGNAL OUT of the fiber card in the primary display...
For more information, refer to the Gen VI Radio Installation Manual (DD2362277), provided with the receiver unit and available online at www.daktronics.com/manuals. All Sport / RC-200 / DAK Score...
Maintenance & Troubleshooting Disconnect power before doing any repair or maintenance work on the display� Permit only qualified service personnel to access internal display electronics. Disconnect power when not using the display� Visual Structural Inspection At least once a year, check the display to ensure the structure and components are in good condition.
Setting the Driver Address Reference Drawings: Address Table; Rotary Switches H and L ............DWG-1198765 Since the same LED drivers can be used for many display models, each driver must be set to receive the correct signal input, or address, for the model in which it is being used.
Replacement Parts The following table contains display components that may require replacement. Many of the other components will have attached part number labels. Description Part Number 18" Red Digit 0A-1611-5113 18" Amber Digit 0A-1611-5213 24" Amber Horizontal Segment (top/bottom) 0A-1611-5221 24"...
Fill out and attach the enclosed UPS shipping document. c� Ship the part to Daktronics. 3� The defective or unused parts must be returned to Daktronics within 5 weeks of initial order shipment� If any part is not returned within five (5) weeks, a non-refundable invoice will be presented to the customer for the costs of replenishing the exchange parts inventory with a new part.
Repair & Return Program For items not subject to exchange, Daktronics offers a Repair & Return Program. To send a part for repair, follow these steps: 1� Call Daktronics Customer Service� United States & Canada: 1-800-DAK-TRON (325-8766) Outside the U.S. & Canada: +1-605-275-1040 2�...
FA, TI-2042; 18" 4-Digit, Pace of Game ............DWG-4061173 FA, TI-2041; 24" 4-Digit, Pace of Game ............DWG-4062341 Shop; TI-2042, 18" Digit Pace of Game Display ..........DWG-4071669 Shop; TI-2041, 24" Digit Pace of Game Display ..........DWG-4071670 Schematic; Dual Power Supply to Driver ............DWG-4072677 Reference Drawings...
Page 22
THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS DRAWING ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. ALL WIRE IS 18 AWG EXCEPT FOR COPYRIGHT 2018 DAKTRONICS, INC. (USA) SIGNAL/COMM CABLES 18"...
Page 23
THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS DRAWING THIRD ANGLE PROJECTION ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. COPYRIGHT 2018 DAKTRONICS, INC. (USA) PITCH TIME FOR BASEBALL PROJECT: SYSTEM RISER;...
Page 24
STANDOFF, 6-32X9/16 F-F, 1/4 HEX ALUM (TB-1137) 20.0 IN LB ± 2.0 IN LB SCREWS LL-2224 LABEL, DAKTRONICS, .50 IN WHITE VINYL DIE CUT LL-2306 LABEL, SERIAL NO./SPECS, 2 WINDOWS, PER DWG 92515 LL-2602 LABEL, ELECTRIC SHOCK HAZARD, YELLOW W/ BLACK TEXT LL-2666...
Page 25
POWER 0A-1611-0025 12" W/B/G-Y OUTDOOR SHEETMETAL SCOREBOARDS DISPLAY W/ AMBER DIGITS, 0A-1753-0315 PROJECT: GROUND 0A-1611-0003 6" FA, TI-2041, 24" 4-DIGIT, PACE OF GAME, RED TITLE: MODEL NO. TI-2041, 24" 4-DIGIT, AMBER FRONT VIEW POWER 0A-1782-0239 48" 16-SEP-19 INCHES [MILLIMETERS] 100V - 240V AC PRIMARY...
Page 26
USE HOLES IN FRONT FLANGES OF CABINET TO ATTACH THE DISPLAY TO THE SIGN FACE USING APPROPRIATE HARDWARE. DAKTRONICS IS NOT RESPONSIBLE FOR THE MOUNTING STRUCTURE OR FOR THE ADEQUACY OF ATTACHMENT TO THE STRUCTURE. STRUCTURE AND ATTACHMENT MUST CONFORM TO ALL APPLICABLE BUILDING CODES.
Page 27
USE HOLES IN FRONT FLANGES OF CABINET TO ATTACH THE DISPLAY TO THE SIGN FACE USING APPROPRIATE HARDWARE. DAKTRONICS IS NOT RESPONSIBLE FOR THE MOUNTING STRUCTURE OR FOR THE ADEQUACY OF ATTACHMENT TO THE STRUCTURE. STRUCTURE AND UPDATED RECOMMENED SIGN FACE OPENING FROM ATTACHMENT MUST CONFORM TO ALL APPLICABLE BUILDING CODES.
Page 28
ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF NOTES: TERMINATE TO GROUND LUG. DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. COPYRIGHT 2018 DAKTRONICS, INC. (USA) 24" PACE OF GAME PROJECT: SCHEMATIC; DUAL POWER SUPPLY TO DRIVER...
Daktronics Warranty & Limitation of Liability This section includes the Daktronics Warranty & Limitation of Liability statement (SL-02374)� Daktronics Warranty & Limitation of Liability...
Page 31
Warranty Coverage. Daktronics warrants to the original end user (the “End User”, which may also be the Purchaser) that the Equipment will be free from Defects (as defined below) in materials and workmanship for a period of one (1) year (the “Warranty Period”). The Warranty Period shall commence on the earlier of: (i) four weeks from the date that the Equipment leaves Daktronics’...
Page 32
In no event shall Daktronics be liable for loss, damage, or injury of any kind or nature arising out of or in connection with this Warranty in excess of the Purchase Price of the Equipment. The End User’s remedy in any dispute under this Warranty shall be ultimately limited to the Purchase Price of the Equipment to the extent the Purchase Price has been paid.
Page 33
For End User’s protection, in addition to that afforded by the warranties set forth herein, End User may purchase extended warranty services to cover the Equipment. The Extended Service Agreement, available from Daktronics, provides for electronic parts repair and/or on-site labor for an extended period from the date of expiration of this warranty. Alternatively, an Extended Service Agreement may be purchased in conjunction with this Warranty for extended additional services.