Table of Contents
Advertisement
Available languages
Available languages
PARTS INCLUDED WITH HOOD
Micromesh Grease Filters
(2 per hood)
3¼" x 10"
Damper / Duct
Connector
Use this template for marking; do not attempt to cut out the ducting hole through it.
M
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
ARK WHERE INDICATED
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
FOR THE APPROPRIATE SIZE DUCT OPENING
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l'installation; elles ne doivent pas
7" R
OUND
D
UCTING
OR
R
ECTANGULAR
D
UCTING
être du format exact des conduits.
= 3¼" x 10"
= 3¼" x 14"
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
M
ARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
C
Bend template along graduated
scale when installing to framed
C
ONDUIT ROND DE
7
PO
OU
C
ONDUIT RECTANGULAIRE
cabinet.
= 3¼ po x 10 po
Pour une installation sous une
= 3¼ po x 14 po
armoire à fond en retrait, utiliser les
lignes pour mesurer l'épaisseur du
décalage causé par le mur de
T
S
l'armoire et plier le gabarit en
8"
ITLE TO BE TRANSLATED IN
PANISH
conséquence.
C L
To be translated in Spanish.
C
ONDUCTO REDONDO
O
C
ONDUCTO RECTANGULAR
7
.
= 3¼ pulg. x 10 pulg.
DE
PULG
= 3¼ pulg. x 14 pulg.
7½"
Electrical access hole center
A = single blower hood
B = double blower hood
V RTICAL EX
VERTICAL EXHAUST
A
A
S
Centre du trou pour fil
d'alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
10½"
To be translated in Spanish
Electrical access hole center
4¼"
A = single blower hood
B = double blower hood
14½"
A
B
C
C
Place this edge against back wall
Appuyer ce bord au mur arrière
Apoyar este borde contra la pared de atrás
Parts Bag
(4 no. 8-18 x 1/2" metal screws,
4 washers, 6 no. 8 x 5/8" round head
wood screws, 6 no. 8 x 1/2" countersunk
wood screws, 1 suction cup tool)
Screwdriver
(Flat & Phillips no. 2)
Pencil
Shielded Halogen Bulbs
(120 V, 50 W max., MR16 or
PAR16 with GU10 base)
(2 per hood)
7" Round
Duct Connector
EZ-1 One person Installation Kit
(including template for
ducting, printed both sides,
and installation brackets)
TOOLS NEEDED FOR HOOD INSTALLATION
and 1½" hole saw)
HR0064
Sheet Metal
Shears
PARTS NOT INCLUDED WITH HOOD
OPTIONAL PARTS (purchase separately)
Ducting Accessories
(See "Equivalent Duct Length Chart" on page 6 for
Ducting Accessory Model Nos.)
"Parts Not Included With Hood" available by calling
Sears at 1-800-4-MY-HOME
Drill
(with 1/8" and
7/64" drill bits,
Tape
Measure
5
Non-Ducted Recirculation Filters
(Non-ducted hoods only)
(2 per hood)
Part Nos.:
S97020466 (30-in. width hoods)
S97020467 (36-in. width hoods)
7-inch Round Damper
(For use with 7-inch Round Duct)
Sears Part No. 59183
Long Nose
Metal Foil
Pliers
Duct Tape
-or-
Keyhole
Saw
Sabre Saw
Wire
Stripper
*
®
Advertisement
Chapters
Table of Contents
