Table of Contents
Advertisement
Available languages
Available languages
PARTS INCLUDED WITH HOOD
Micromesh Grease Filters
(2 per hood)
3¼" x 10"
Damper / Duct Connector
7" Round Duct Connector
Use this template for marking; do not attempt to cut out the ducting hole through it.
M
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
ARK WHERE INDICATED
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
FOR THE APPROPRIATE SIZE DUCT OPENING
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l'installation; elles ne doivent pas
7" R
OUND
D
UCTING
OR
R
ECTANGULAR
D
UCTING
être du format exact des conduits.
= 3¼" x 10"
= 3¼" x 14"
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
EZ-1 One person Installation Kit
M
ARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
C
Bend template along graduated
scale when installing to framed
C
ONDUIT ROND DE
7
PO
OU
C
ONDUIT RECTANGULAIRE
cabinet.
= 3¼ po x 10 po
Pour une installation sous une
= 3¼ po x 14 po
armoire à fond en retrait, utiliser les
lignes pour mesurer l'épaisseur du
décalage causé par le mur de
T
S
l'armoire et plier le gabarit en
8"
ITLE TO BE TRANSLATED IN
PANISH
conséquence.
C L
To be translated in Spanish.
C
ONDUCTO REDONDO
O
C
ONDUCTO RECTANGULAR
(including template for
7
.
= 3¼ pulg. x 10 pulg.
DE
PULG
= 3¼ pulg. x 14 pulg.
7½"
Electrical access hole center
A = single blower hood
B = double blower hood
VERTICAL EXHAUST
V RTICAL EX
A
A
S
Centre du trou pour fil
d'alimentation électrique
ducting, printed both sides,
A = hotte ventilateur simple
B = hotte ventilateur double
10½"
To be translated in Spanish
Electrical access hole center
4¼"
A = single blower hood
B = double blower hood
14½"
A
B
and installation brackets)
C
C
Place this edge against back wall
Appuyer ce bord au mur arrière
Apoyar este borde contra la pared de atrás
Parts Bag
(4 no. 8-18 x 1/2" metal screws,
6 no. 8 x 5/8" round head wood screws,
6 no. 8 x 1/2" countersunk wood screws)
Screwdriver
(Flat & Phillips no. 2)
TOOLS NEEDED FOR HOOD INSTALLATION
Pencil
HR0064
Sheet Metal
Shears
PARTS NOT INCLUDED WITH HOOD
OPTIONAL PARTS (purchase separately)
"Parts Not Included With Hood" available by calling
Drill
(with 1/8" and
7/64" drill bits,
and 1½" hole saw)
Tape
Measure
5
Non-Ducted Recirculation Filters
(Non-ducted hoods only)
(2 per hood)
Part No. S97020466
7-inch Round Damper
(For use with 7-inch Round Duct)
Part No. 59183
1-844-553-6667
Long Nose
Pliers
-or-
Keyhole
Saw
Sabre Saw
Wire
Stripper
Metal Foil
Duct Tape
Advertisement
Chapters
Table of Contents
