Related Manuals for Kenmore 31130
Summary of Contents for Kenmore 31130
-
Page 1: Range Hood
Range Hood Use & Care Guide Installation Manual Models 31130 (30” wide - Stainless) 31133 (36” wide - Stainless) HB0108 09030 rev. A SEARS CANADA INC., Toronto, Ontario M5B 2B8 www.sears.ca... -
Page 2: Table Of Contents
Open a window close to or in the kitchen. Peppercorn Beef Flambé). 10. To reduce the risk of fi re and electric shock, the Kenmore Elite 3. Clean ventilating fan frequently. Grease should not be allowed hood should only be installed with its own built-in blower. -
Page 3: Operation
OPERATION OPERATION Always turn ON your hood before you begin cooking in order Nigthlight switch to establish an air fl ow in the kitchen. Let the blower run for a Press this switch once to turn on the nightlight. Press this switch few minutes to clear the air after you turn off the range. -
Page 4: Parts Included With Hood
PARTS INCLUDED WITH HOOD PARTS INCLUDED WITH HOOD Aluminum grease fi lters (2 per hood) HR0010 Parts Bag including: 5 no. 8 x 1½” countersunk screws 8 no. 8 x 3/4” screws 6 no. 8 x 3/8” screws 6 Drywall anchors 3 Washers HR0051 Decorative fl... -
Page 5: Range Hood System
3¼” x 10” Duct Ductwork 8” Round Standard Duct Adapter/damper Lower Adapter/damper 8” round (supplied Decorative 3¼” x 10” (supplied with hood) Flue with hood) For vertical discharge For horizontal discharge Adapter/dampers 31130 or 31133 Range Hood HL0142 Single Blower (supplied with hood) -
Page 6: Equivalent Duct Length Chart
EQUIVALENT DUCT LENGTH CHART Kenmore range hoods are designed to perform effi ciently when attached to long runs of duct. As a point of reference, this hood will function at approximately 80% of its rated air performance when 300 equivalent feet of 8” round ductwork is attached. Use this chart to calculate the equivalent duct length of your system. -
Page 7: Select Installation Type
SELECT INSTALLATION TYPE 1. Plan where and how the ductwork will be installed. Install proper-sized ductwork, transition(s), elbow(s), and OOF CAP roof or wall cap. 8” ROUND DUCT For best results, use a minimum number of transition and elbows. 2. The minimum hood distance above cooktop must not be less than 24’’. -
Page 8: Wiring Installation
WIRING INSTALLATION WARNING: Improper grounding can result in a risk of electric shock. Consult a qualifi ed electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded. Do not use an extension cord. If the power supply cord is too short, have a qualifi... -
Page 9: Prepare The Hood
PREPARE THE HOOD 1. Lay the hood on its back on a table. Remove grease fi lters by lifting the metal latch tab (1), pushing down on the fi lter (2) and tilting is towards you (3). NOTE Use a piece of cardboard to avoid damaging the table or the hood. - Page 10 11. These Kenmore Elite Series range hoods are factory shipped with the blower mounted for a vertical discharge confi guration. For a horizontal discharge confi guration, disassemble the blower from the inner top of the hood (see illustrations below). It will be assembled to the inner back of the hood once the hood is mounted on the wall.
-
Page 11: Install The Hood
INSTALL THE HOOD WARNING: When cutting or drilling into wall, do not damage electrical wiring and other hidden utilities. 1. Construct wood wall framing that is fl ush with surface of wall studs. Wood wall framing must be at least 1/2” thick and 3” high. Ensure to assemble wood wall framing to wall studs for a solid installation. -
Page 12: Finalize The Installation
INSTALL THE HOOD INSTALL THE HOOD ERTICAL DISCHARGE ONLY ERTICAL DISCHARGE ONLY 6. Mount the 8” round adapter/damper (included in a separate 7. Plug hood power cord into the outlet. box) to the hood using 4 no. 8 x 3/8” sheet metal screws Slide a 8”... -
Page 13: Installing Grease Filters
FINALIZE THE INSTALLATION PPER FLUE MOUNTING BRACKET RONT VIEW 3. Slide up the upper fl ue until it is aligned with its mounting bracket. The bracket must be inside the flue. Secure the upper fl ue to its bracket using 2 no. 8 x 3/8” screws (included). -
Page 14: Service Parts
SERVICE PARTS HOOD WIDTH EY NO ART NO ESCRIPTION 30” 36” 18504 PPER FLUE MOUNTING BRACKET 18494 PPER DECORATIVE FLUE 18496 OWER DECORATIVE FLUE 8” OVER PLATE FOR ROUND 18515 TOP EXHAUST LECTRONIC CONTROL MODULE 18522 INCLUDING VERLAY ITEM 07322 VERLAY 05917 (GU10)