Test The Safety Reverse System; Program Your Opener And Remote / The Wireless Push Button (Optional); Connect The Internet Gateway - Chamberlain EVOLUTION LM60EVFA Assembly And Operating Instructions Manual

24

Test the Safety Reverse System

The safety reverse system test is important. Garage door
must reverse on contact with a 50 mm obstacle laid flat
on the floor. Failure to properly adjust opener may result
in serious personal injury from a closing garage door. Repeat test
once a month and adjust as needed.
OBSTACLE TEST:
Place a 50 mm high obstacle (1) under the garage door on the floor.
Move door downwards� The door must reverse when it comes into
contact with the obstacle� If upon contact the door stops, the door does
not move down far enough� In this case repeat limit setting� If the door
reverses after contact with the 50 mm high obstacle, remove obstacles
and open and close the door completely once� The door should not go
back, if it reaches the door position „Closed"� If it still reverses both
limits must be reprogrammed�
OPENING TEST: Apply 20 kg to the middle of the door�
The door should not open completely�
For side moving sectional doors follow the requirements as defined un-
der 6F� The side moving sectional door must reverse in closing direction
on contact with a 50 mm obstacle between the main closing edge and
opposite edge� In open direction the door must stop�
25 Program your opener and remote / the
Wireless push button
Activate the opener only when door is in full view, free of obstruc-
tion and properly adjusted. No one should enter or leave garage
while door is in motion. Do not allow children to operate push
button(s) or remote(s). Do not allow children to play near the door.
Your garage door opener receiver and one of the buttons remote control
are pre-programmmed� If you purchase additional remote controls, the
garage door opener must be programmed to accept the new remote
code�
Program the Receiver to Match Additional Remote Controls:
Using the yellow round button.
1� Press and release the yellow round button on the opener� The
learn indicator light will glow steadily for 30 seconds (1)�
2� Within 30 seconds, press and hold the button on the hand-held
remote that you wish to operate your garage door (2)�
3� Release the button when the opener light blinks once� It has
learned the code� Now the opener will operate when the remote
control push button is pressed� If you release the remote control
push button before the opener light flashes, the opener has not
learned the code�
(optional)
To Erase all Remote Control Codes
To deactivate any unwanted remote, first erase all codes: Press and
hold the yellow round button on opener until the learn indicator light
goes out (approximately 10 seconds)� All previous codes are now er-
ased� Reprogram each remote or keyless entry you wish to use�
26

Connect the Internet Gateway

Before starting you MUST have:
• a router
• active internet connection
• a free "Ethernet" terminal on your router
• internet gateway serial number (on the backside of the device)
• a pair of photocells connected to the garage door opener� If there are
no photocells connected the garage door can only be opened�
WARNING!
To prevent possible SERIOUS INJURY or DEATH:
• When the Internet Gateway is used with a garage door opener, the
opener MUST ONLY be installed with sectional doors�
• Never allow children playing with the garage door, the remote control,
wall-switches or any other accessories�
• Operate the garage door only when it is technically faultless and the
door area is free of obstructions or people�
• This product allows operating the garage door without visual control�
• Therefore the door may execute unexpected travels� Never pass
through a closing garage door�
• For resindential use only� Only instructed poeple may use this
• product�
• Some parts of the car (doors, trunk lids) may extend into the travel
path and cause serious damage to the garage door and/or the car�
• The serial number on the backside of this device is for your personal
use only� Save this numer from others�
1. Connect
Connect the provided ethernet cable (1) to router (2)� Use the plug valid
for your country ( not all models)� Connect power (3) to the internet
gateway (4)� When the internet gateway connects to the internet, the
green light (5) will stop blinking and will light solid�
2. Create an account
Download the free myQ App from App Store or Google Play Store and
create an account� If you already have an account, use your username
and password�
3. Register the internet gateway
Enter the Serial Number located on the bottom of the internet gateway
when prompted�
en 7