Full Gauge Controls Microsol SWP Advanced c-o-n-n-e-c-t Manual page 2

7. SETTINGS - USER LEVEL
Access the settings menu by pressing the SET key (short press). Use the
11111keys to select the desired function. This value can be edited with a short press on the
SET key. Use the
and keys to change the value, and when ready, give a short
press on the SET key to memorize the set value and return to the functions menu.
To exit the menu and return to normal operation (temperature display) press the SET key
(long press).
7.1 POOL/RESERVOIR HEATING TEMPERATURE (SENSOR
T2)
When accessing user settings, it is possible to adjust the Setpoint configuration.
SP - Pool/reservoir temperature setpoint:
Sets the desired control temperature for the pool/reservoir.
8.1 PARAMETERS TABLE
TECHNICAL
FUN DESCRIPTION
CODE Access code
TC.01 Controller language
TC.02 Temperature unit
TC.03 Fluid type
TC.04 Estimated pump flow
TC.05 Flow unit (volume)
TC.06 Power unit
8.2 DESCRIPTION OF PARAMETERS
CODE - Access code:
It is necessary when you want to change the configuration parameters. To only
visualize the adjusted parameters it is not necessary to insert this code.
Code 231 - Technician
Code 123 - Advanced
TC.01 - Controller language:
Selects the language for displaying messages on the controller:
PORT = Portuguese;
ESP = Spanish;
ENG = English.
TC.02 - Temperature unit:
Selects the controller temperature unit:
°C = Celsius;
°F = Fahrenheit.
Note: When the unit is changed, the controller goes into pause mode and reconfigures
the parameters for the new unit, restarting the operation soon after.
TC.03 - Type of fluid:
Informs the type of fluid used in the collector. Information used to estimate the amount of
energy absorbed by the solar heating system:
WATE = Water;
GLIC = Propylene glycol solution.
TC.04 - Estimated pump flow:
Informs the estimated flow rate of the pump. Information used to estimate the amount
of energy absorbed by the solar heating system.
9.1 PARAMETERS TABLE
ADVANCED
FUN DESCRIPTION
CODE
Access code
Differential (T1-T2) to start the pump
DF.01
Differential (T1-T2) to turn off the pump
DF.02
Minimum T2 (pool/reservoir) superheat temperature setpoint
DF.03
allowed to the user
Maximum superheat temperature setpoint T2 (pool/reservoir)
DF.04
allowed to the user
T2 superheat temperature to turn off the pump
DF.05
T2 superheat temperature hysteresis to restart the pump
DF.06
Antifreeze temperature T1 to start the pump
DF.07
Minimum antifreeze time
DF.08
T1 superheat temperature to turn off the pump
DF.09
Pump on time in manual mode
DF.10
Temperature sensor T3 to turn off cooling in Holidays mode
DF.11
Minimum temperature T1 to start the pump - scan mode
DF.12
Pump on time - scan mode
DF.13
Pump off time - scan mode
DF.14
Maximum differential (T1-T2) for thermal shock protection
DF.15
8. SETTINGS - TECHNICAL LEVEL
Access the installation settings menu by pressing the SET key for 4 seconds until CODE
and
appears. Then press the SET key again (short press). Use the
the value of the access code 231, and when ready press the SET key again (short
press).
Use the
key it is possible to edit its value. Use the
ready, give a short press on the SET key to memorize the set value and return to the
functions menu. To exit the setup menu and return to normal operation, press the SET
key (long press).
CELSIUS
MINIMUN MAXIMUN UNIT
-
0 9999
-
PORT ENG
-
°C °F
-
WATE GLYC
l/m
1 999
-
LITER GALL
-
kWh MBTU
TC.05 - Flow unit (volume):
Defines the desired flow unit to display the estimated energy absorbed by the solar
heating system.
TC.06 - Power unit:
Selects the desired energy unit to display the estimated energy absorbed by the solar
heating system.
9. SETTINGS - ADVANCED LEVEL
Access the settings menu by pressing the SET key for 4 seconds. Then CODE will
appear and then press the SET key again, short press. Use the
the access code value, 123, and when ready press the SET key again (short press). Use
the 11
possible to edit its value. Use the
give a short press on the SET key to memorize the set value and return to the functions
menu. To exit the menu and return to normal operation (temperature display) press the
SET key (long press).
When accessing the adjustment of a parameter, the display will be flashing indicating that
it is SET possible to change the parameter value.
If you have not entered code 123, the adjustment will be locked and when pressing the
1111and
Cod X
to change the function value, the controller will display the message
display and it will not be possible to adjust the parameter.
CELSIUS
MINIMUN MAXIMUN UNIT
-
0 9999
°C
1.0 40.0
°C
1.0 40.0
°C
-20.0 DF.04
°C
DF.03 105.0
°C
DF.03 DF.04
°C
0.1 20.0
°C
OFF(-20.0) 10.0
seconds
OFF(0) 600
°C
0.0 200.0
minutes
1 720
-
OFF ON
°C
0.0 105.0
seconds
OFF(9) 999
minutes
1 999
°C
OFF(0.0) 200.0
keys to select the desired function. With a short press on the SET
and
and
DEFAULT MINIMUM MAXIMUN
0 0
PORT PORT
°C °C
WATE WATE
50 1
LITER LITER
kWh kWh
keys to select the desired function. With a short press on the SET key it is
or D
or keys to change the value, and when ready,
keys to change the value of the function, the controller will show the message
on the display. With the function lock active, when pressing the
DEFAULT MINIMUM MAXIMUN
0 0
8.0 1.0
4.0 1.0
-20.0 -4.0
105.0 DF.03
32 DF.03
1.0 0.2
8.0 OFF(-4.0)
60 OFF(0)
70.0 32.0
360 1
OFF OFF
35.0 32.0
20 OFF(9)
30 1
OFF(0.0) OFF(32.0)
and keys to enter
keys to change the value and, when
FAHRENHEIT
UNIT DEFAULT
-
9999 0
-
ENG PORT
-
°F °C
-
GLYC WATE
l/m
999 50
-
GALL LITER
-
MBTU kWh
or keys to enter
and keys
on the
FAHRENHEIT
UNIT DEFAULT
-
9999 0
°F
72.0 14.4
°F
72.0 7.2
°F
DF.04 -4.0
°F
221.0 221.0
°F
DF.04 89.6
°F
36.0 1.8
°F
50.0 46.4
seconds
600 60
392.0 °F
158.0
minutes
720 360
-
ON OFF
°F
221.0 95.0
seconds
999 20
minutes
999 30
°F
392.0 OFF(0.0)