Related Manuals for Z GRILLS Australia 700E-XL
Summary of Contents for Z GRILLS Australia 700E-XL
- Page 1 Z Grills 700E-XL Wood Pellet Smoker Grill Owner Manual www.zgrills.com.au This owner manual edition is for Z Grills 700E-XL (V6) with Wireless Controller...
- Page 2 Quick Reference Guide INITIAL STARTUP PROCEDURE • The FEED PELLET process must be completed before first use and each time after the grill runs out of wood pellets. See section 4 for details. NEW GRILL BURN IN • It is important to complete a 45 minute high temperature BURN IN before cooking any food on a new Z Grill.
- Page 3 IMPORTANT SAFETY INFORMATION DANGER! • FLAMMABLE LIQUIDS: Never use or store flammable liquids near the grill, or use flammable liquids to light the grill. • OUTDOOR USE ONLY: Do not operate the grill indoors or in enclosed spaces as carbon-monoxide poisoning may occur. The grill may be used in an open air deck or balcony as long as SAFE DISTANCE guidelines are met and smoke is able to freely vent from the ceiling/roof area.
-
Page 4: Table Of Contents
6. Cleaning the Grill 7. Error Codes 8. Technical Specifications 9. Wiring Diagram 10. Spare Parts List 11. Food Temperature Chart 12. Troubleshooting 13. Grill Repair Instructions 14. Limited Product Warranty © Z Grills Australia Pty Ltd - 2023 04-08-2023... -
Page 5: Main Grill Components
1. Main Grill Components Hopper Bottom Assembly Chimney Gasket Hopper Feed Chute Grease Bucket Grill Lid Grill Base & Cabinet Grill Lid Handle Heat Baffle Fire-pot Vented Grease Tray Grill Temperature Sensor Bottom Grilling Rack (Right) Thermal Insulating Liner Bottom Grilling Rack (Left) Grill Drum Top Grilling Rack Chimney Cap... -
Page 6: Unpacking & Assembly Instructions
2. Unpacking & Assembly Instructions The boxes and some of the components are heavy. Two people are required to safely complete the assembly process. Unpacking • Do not place painted metal components directly on bricks or concrete as it may scratch the paint. - Page 7 STEP 1 - WHEELS STEP 5 - FRONT BRACE Two holes towards the front Rear Wheels with Lock STEP 2 - DOOR MAGNETS Screws are already attached to the base STEP 6 - HOPPER ASSEMBLY If the magnets don’t lock into place, pinch the sides so the “wings”...
- Page 8 STEP 7 - DRUM & BASE ASSEMBLY TIPS: 1. Lock the rear wheels so the base doesn’t move around. 2. Make sure the base is on a flat surface. 3. Use two people to lift the drum up onto the base. 4.
- Page 9 STEP 9 - HOPPER LID HANDLE STEP 11 - CHIMNEY White Fibre Handle Gasket TIP: Cover the opening of the hopper with a piece of cardboard to prevent the kep nuts accidentally falling into the auger. STEP 10 - GRILL LID HANDLE STEP 12 - DOOR HANDLES Left &...
- Page 10 STEP 14 - HEAT BAFFLE TIPS: 1. Gently slide the heat baffle in and out of the slots. Using force will make it more difficult to remove. 2. Only remove the heat baffle once the grill has completely cooled down. REMOVE INSERT STEP 15 - GREASE TRAY...
-
Page 11: Wireless Controller
3. Wireless Controller The controller monitors the temperature sensor inside the grill and turns on/off the auger to deliver wood pellets into the fire-pot as well as managing the fan speed. The grill internal temperature and four food temperature probes can be monitored on the controller display. - Page 12 Controller Functions Press and hold the control knob for 2 seconds to enter the menu. Below is a summary of all menu items. Software is updated from time to time, so scan the QR code at the bottom of this page for the most up to date summary. FIRE UP Fires up the grill.
- Page 13 Install the App on your mobile device and then follow the instructions to set up a free account. Detail instructions on how to connect a Z Grills wood pellet smoker grill can be found by scanning the instructions QR code below, or going to: zgrills.com.au/wifi-controller...
-
Page 14: Pellet Feed & Burn In
4. Pellet Feed & Burn In Complete the Pellet Feed process before first use, and each time after the grill runs out of wood pellets. Pellet Feed Remove grill racks, grease tray and heat baffle from the grill. Open the pellet hopper and grill lids and check to ensure there are no foreign objects in the hopper or auger. -
Page 15: Normal Grill Operation
5. Normal Grill Operation Fire Up The Grill With the grill plugged into power, press the controller knob to turn the power on. Open the grill lid and check that there are enough wood pellets in the hopper. Press and hold the control knob for 2 seconds to enter the MENU, then rotate to select FIRE UP and press again to select. - Page 16 If the hopper is totally empty of wood pellets, follow the Initial Fire Up Process to fill the the auger tube with fresh wood pellets. High Temperature Searing This Z Grills 700E-XL (V6) features a vented grease tray that allows for high temperature searing on the left hand side of the grill.
-
Page 17: Cleaning The Grill
6. Cleaning the Grill Clean the Grill after each use, as accumulation of grease, ash and soot can increase the risk of a grease fire and result in inefficient operation. Grease Tray, Drain & Bucket • Remove foil from the grease tray and wipe off any surface grease. •... -
Page 18: Error Codes
7. Error Codes Error codes will be displayed on the controller LCD screen. The grill will begin the Shut Down cycle or turn OFF if there is an ERROR. The problem must be solved before the grill can operate normally again. Check the Troubleshooting section for more detailed information, or scan the QR code for help with error troubleshooting. -
Page 19: Technical Specifications
8. Technical Specifications Grill Model ZPG-700E (V6) also called 700E-XL Wireless Controller Colour LCD screen, WIFI enabled Bottom Grill Rack 488 x 660 mm (0.322m Top Grill Rack 345 x 660 mm (0.228m Grease Tray Type Vented holes for BBQ plate searing Total Grilling Area 0.55 m (850 square inches) -
Page 20: Spare Parts List
10. Spare Parts List If a component is damaged, lost or just worn out through normal use, spares are available. Please refer to the chart below for most common spare components. Visit our website zgrills.com.au to order spare parts, or contact our support team. Component Description Part Name Grill Temperature Sensor... -
Page 21: Troubleshooting
No smoke or fire FAILURE unclear, touch with a long twisted piece of paper. • If not getting hot, contact Z Grills Australia customer support for a replacement part. • Moist pellets will not burn well and the fire can go out. - Page 22 • Check the sensor plug located between the grill drum and hopper. • Check the sensor connection into the back of the controller (with the grill power unplugged) FAULTY GRILL • If still getting HIGH TEMP errors contact Z Grills customer TEMPERATURE support for a replacement temperature sensor. SENSOR •...
- Page 23 Problem Reason Investigation/Solution • After Firing Up the grill, don’t shut the lid until lots of smoke is released and the fire has burnt for a few minutes. Temperature rises • Shutting the lid too early results in the large initial quantity of too high (above pellets releasing lots of heat which easily overshoots lower temperature settings on hot days.
-
Page 24: Grill Repair Instructions
Do not complete any repair work yourself unless suitably experienced and confident to do so. • Refer to the table below for estimated time, difficulty, parts and tools required. • How to repair videos are available on the Z Grills Australia website. Component Time Difficulty Spare Parts Tools Required ✓... -
Page 25: Limited Product Warranty
Manufacturer’s Limited Warranty Policy Z Grills Australia Pty Ltd (Z Grills) provides a 3 years parts warranty from the date of purchase by the original owner. This warranty applies to defects in all materials and workmanship. - Page 26 Knowledge Centre To get the most out of your smoker, scan the QR code to visit our Knowledge Centre. Articles are regularly added and updated covering a wide range of topics from the basics of how to use your grill, through to expert tips and troubleshooting guides. Scan QR code zgrills.com.au/help/ Or go to:...