Related Manuals for Z GRILLS ZPG-L600D
Summary of Contents for Z GRILLS ZPG-L600D
- Page 1 WOOD PELLET GRILLS ZPG-L600D/ZPG-L600E OWNER’S MANUAL MON TO FRI, 8:00 A.M. - 5:00 P.M. PACIFIC STANDARD TIME SERVICE CONTACT: 1-833-947-4557/1-833-ZGRILLS EMAIL: support@zgrills.com WEBSITE: www.zgrills.com VN092020...
-
Page 3: Table Of Contents
CONTENTS IMPORTANT SAFETY INFO COMPONENT LIST ASSEMBLY INSTRUCTIONS INITIAL FIRING INSTRUCTIONS SUBSEQUENT START-UP OPERATING TIPS MAINTENANCE & CLEANING TROUBLESHOOTING DIGITAL THERMOSTAT CONTROL WIRING DIAGRAM Z GRILLS SUPPORT 3-Y LIMITED WARRANTY... - Page 4 SAVE THIS MANUAL FOR FUTURE REFERENCE...
-
Page 5: Important Safety Info
IMPORTANT SAFETY INFO GENERAL WARNINGS Please read this entire manual before installation and use of the pellet fuel-burning appliance. Failure to follow these instructions could result in property damage, bodily injury or even death. Contact local building or fire officials about restrictions and installation inspection requirements in your area. - Page 6 DO NOT place anything heavy on top of hopper lid. It is not a shelf and is a tip hazard. Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or ‘freshen up’ a fire in this appliance. Keep all such liquids well away from the appliance when in use.
- Page 7 There is no guarantee that other brands of pellets are suitable for use in Z GRILLS. And Z GRILLS assumes no liability for any loss, damage or injury caused by the use of any other brands of pellets.
-
Page 8: Component List
COMPONENT LIST ITEM DESCRIPTION ITEM DESCRIPTION Grill Chamber Assembly Fixed Plate Furnace Hinge Lid Hinge Digital Control Lower Hopper Safety Grate Lid Handle Cable Clip Hopper Burner Lid Power Cord Hopper Assembly Hot Rod (Ignitor) Hopper Handle Fixed Tube Grease Drain Pan Left Support Hopper Insulation Gasket RTD Temperature Probe Auger... - Page 9 HARDWARE PACKAGE LIST ITEM DESCRIPTION ITEM DESCRIPTION Pin Shaft Bolt 1/4-20×1/2 Bolt 1/4-20×32 Open End Wrench Bolt 8#-32×3/8 Gasket (Ø20*Ø6.5*2.0mm) Gasket (Ø6.5*Ø12*1.2mm) Spring Washer Step Screw 8#-32 (Ø6.5*Ø9.5*1.5mm) Bolt 1/4-20×7 Hexagon Bolt 1/4-20 Hexagon Nut 1/4-20 Bolt 8#-32×1/2 Screwdriver Bolt 1/4-20×15 Thumb Screw 8#-32×3/8 Hexagon Nut 1/4-20 Hexagon Kep Nut 8#-32...
-
Page 10: Assembly Instructions
ASSEMBLY INSTRUCTIONS PARTS DIAGRAM HOPPER BURNER ASSEMBLY... - Page 11 BODY FRAME ASSEMBLY 1. MOUNTING THE BODY FRAME 1. Turn the Platform (53) upside down. Install the wheels (51)(52) in the screw holes. Tighten with wrench (L). 2. Secure Left Plate (45) on the Platform (53) with Bolt (A).
- Page 12 3. Secure Right Plate (57) on the Platform (53) with Bolt (A). 4. Secure Back Plate (58) on the Platform (53) and connect to Left Plate (45) and Right Plate (57) with Bolt (A) . 5. Attach the Beam (44) between Left Plate (45) and Right Plate (57) with Bolt (A).
- Page 13 6. Assemble the Magnet Base (46) to the platform (53) with Bolt C. 2. MOUNTING THE BODY FRAME TO THE CHAMBER With the help of another person, carefully attach the Grill Chamber Assembly (1) on the Body Frame and using Bolt (A). Use the Screwdriver (S) to tighten. Caution: The grill is very heavy.
- Page 14 3. MOUNTING THE HOPPER TO THE CHAMBER 1. Insert Bolt (C) into Hopper Burner Lid (6) and Hopper Assembly (7), align the holes, then assemble it with Nut (J). Use the Screwdriver (R) to tighten. 2. Assemble Hopper Handle (8) to Hopper Assembly (7) with Bolt (A). 3.
- Page 15 4. ATTACHING THE SMOKESTACK AND CHIMNEY CAP Insert two Bolts (F) through Gasket (M), the two holes in the Smoke Stack Assembly (27) and the two holes in the Smoke Stack Gasket (26). Align and insert through the two holes in the Grill Chamber Assembly (1).
- Page 16 6. POSITIONING THE DOOR 1. Assembly the Right Door (54) to the Body Frame. First insert the Bottom Pivot (49) into the small hole on Platform (53).Then pull down the Right Door Upper Pivot (56) until the upper end is aligned with top edge of the door. Then align the Right Door Upper Pivot (56) with the upper hole and pull up the pivot to secure the door.
- Page 17 8. ATTACHING THE BURNER BOX ASSEMBLY 1. Assemble the Burner Box Assembly (13) to the Hopper Burner Assembly with Bolt (G). 2. Insert Bolt (P) through Fixed Tube (37) and into Burner Box Assembly (13). 9. ATTACHING THE FIRE POT 1.
- Page 18 10. POSITIONING THE GREASE DRAIN PAN LEFT SUPPORT Assemble the Grease Drain Pan Left Support (9) to Chamber with Bolt (A). 11. POSITIONING THE GREASE DRAIN PAN BOTTOM SUPPORT Assemble the Grease Drain Pan Bottom Support (19) to Chamber with Bolt (C) and Nut (J).
- Page 19 12. POSITIONING THE GREASE DRAIN PAN 1. Insert Bolt (H) through Spring Washer (O), Air Door (17), Grease Drain Pan (18), Gasket (N), Nut (I) orderly. Lock with Screwdriver (R) and Wrench (L). As shown. 2. Clip the Grease Drain Pan Left Support (9) into the mounting hole of the Grease Drain Pan (18).
- Page 20 14. HANG ON THE GREASE BUCKET Hang the Grease Bucket (21) on the Hook (22) which through the holes of Bottom Plate, as shown.
-
Page 21: Initial Firing Instructions
Please read this manual carefully and follow it step by step before starting your Z Grills for the first time and each time the grill runs out of pellets. 1.Remove the Porcelain Grills, Grease Drain Pan and Heat Baffle from the interior of the grill. -
Page 22: Subsequent Start-Up
Temperature Dial to any cooking setting desired. 5.If this step is not successful, see TROUBLESHOOTING or contact Z GRILLS Technical Support to help diagnose the problem. -
Page 23: Operating Tips
OPERATING TIPS 1.Like all grills, the actual temperature of this grill and the cooking times will be affected by external temperature, humidity, wind conditions, quality of pellets, etc. 2.It is beneficial to shelter your grill from the wind. This will aid in temperature output, heat retention and heat recovery time when the lid is open. -
Page 24: Maintenance & Cleaning
2.It is highly recommended that you use Z GRILLS Cover to protect your grill . 3.You can use a high-quality car wax on the outside surfaces of your grill to protect it’s finish. - Page 25 Clean the ash from the interior of the grill periodically. If excessive ash is in the firepot, it may cause the fire to go out. This is especially true in the SMOKE setting. A shop vac is an excellent tool to use for removing the ash. WARNING: MAKE SURE THE GRILL FIRE IS OUT, THE UNIT IS OFF, UNPLUGGED AND COLD BEFORE ATTEMPTING TO CLEAN ASH FROM THE GRILL.
-
Page 26: Troubleshooting
TROUBLESHOOTING CAUTION: Make sure the grill is completely cool and unplugged before you do any inspection, cleaning, maintenance or service work. Potential Problem Solution Cause Make sure the power cord is plugged Power in. Verify there is power at the electrical outlet. - Page 27 Pellets pellets. When contacting customer support Contact please have the following information Z GRILLS available: Your authorized Z Grills Customer dealer, your name, phone number, Get your new parts Service or your address, your Z Grill serial number and Z GRILLS part identification number.
-
Page 28: Digital Thermostat Control Wiring Diagram
DIGITAL THERMOSTAT CONTROL WIRING DIAGRAM... -
Page 29: Z Grills Support
Thank you for purchasing a Z GRILL! If you have any question, please contact customer support or your Z GRILL dealer. Z GRILLS, INC. offers the best technical and sales support in the industry. When calling customer please be prepared to provide the following information: 1.Dealer's name and date of purchase... -
Page 30: 3-Y Limited Warranty
Z GRILLS, Inc. shall not be liable if you install, operate, clean or maintain your grill without following the owners' manual instructions. Misuse, abuse, alteration and natural disasters...