CONTENTS IMPORTANT SAFETY INFO COMPONENT LIST ASSEMBLY INSTRUCTIONS INITIAL FIRING INSTRUCTIONS SUBSEQUENT START-UP OPERATING TIPS MAINTENANCE & CLEANING TROUBLESHOOTING DIGITAL THERMOSTAT CONTROL WIRING DIAGRAM Z GRILLS SUPPORT 3-Y LIMITED WARRANTY...
IMPORTANT SAFETY INFO GENERAL WARNINGS Please read this entire manual before installation and use of the pellet fuel-burning appliance. Failure to follow these instructions could result in property damage, bodily injury or even death. Contact local building or fire officials about restrictions and installation inspection requirements in your area.
Page 6
DO NOT place anything heavy on top of hopper lid. It is not a shelf and is a tip hazard. Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or ‘freshen up’ a fire in this appliance. Keep all such liquids well away from the appliance when in use.
Page 7
There is no guarantee that other brands of pellets are suitable for use in Z GRILLS. And Z GRILLS assumes no liability for any loss, damage or injury caused by the use of any other brands of pellets.
COMPONENT LIST ITEM DESCRIPTION ITEM DESCRIPTION Wheels Chamber Hinge Right Front Leg Lid Handle Right Rear Leg Handle Guide Grease Drain Pan Support Furnace Hinge Hopper Lid Grill Chamber Assembly Upper Hopper Safety Grate Smoke Stack Gasket Hopper Part Smoke Stack Hopper Handle Chimney Cap Digital Control...
ASSEMBLY INSTRUCTIONS PARTS DIAGRAM: HOPPER BURNER ASSEMBLY:...
Page 11
1.MOUNTING THE BODY FRAME TO THE CHAMBER 1.Unpack all the items, including the parts packed in the Grill Chamber (6). Turn the body upside down and place upon the original Styrofoam packing material from the carton. (CAUTION: Grill is heavy and requires two people to lift.) 2.Take the Right &...
Page 12
2.MOUNTING THE HOPPER TO THE CHAMBER 1. Take out the screws attached to the Hopper, and then assemble Hopper Lid(27) to the Hopper through hinge holes by these screws. 2. Open the Lid, insert the Hopper into the Chamber, then using the Bolts (E) and Gaskets (D) install it in sequence from inside.
Page 13
4.ATTACHING THE CHAMBER LID HANDLE From the inside of the raised lid, push the Bolts (E) through the gaskets (D) and then through the lid (1) and Handle Guide (4). Handle should sit inside the depression in the guide. Thread Bolts (E) into Handle (3) and tighten with Wrench (I). 5.POSITIONING THE HEAT BAFFLE Position The Heat Baffle (16) on the locating brackets which are on the inside walls of the Grill.
Page 14
6.POSITIONING THE GREASE DRAIN PAN Position The Grease Drain Pan (15) over the Firepot. The notched legs of the Grease Drain Pan should be facing downward to fit onto the locating bracket so that the grease can flow into the Grease Drain Tube. 7.POSITIONING THE PORCELAIN GRILL AND WARMING RACK Position the Porcelain Grill (14) inside the cooking area and locate the Warming Rack (12)(13) on the rack support inside the chamber.
Page 15
8.HANG ON THE GREASE BASKET AND POSITIONING THE ASH TRAY 1.Locate the Grease Drain Tube which is on the right side of the chamber, then hang the Grease Bucket (10) on the hook. 2.Insert the Ash Tray (11) into the Grill Chamber.
Please read this manual carefully and follow it step by step before starting your Z Grills for the first time and each time the grill runs out of pellets. 1.Remove the Porcelain Grills, Grease Drain Pan and Heat Baffle from the interior of the grill.
Temperature Dial to any cooking setting desired. 5.If this step is not successful, see TROUBLESHOOTING or contact Z GRILLS Technical Support to help diagnose the problem.
OPERATING TIPS 1.Like all grills, the actual temperature of this grill and the cooking times will be affected by external temperature, humidity, wind conditions, quality of pellets, etc. 2.It is beneficial to shelter your grill from the wind. This will aid in temperature output, heat retention and heat recovery time when the lid is open.
2.It is highly recommended that you use Z GRILLS Cover to protect your grill . 3.You can use a high-quality car wax on the outside surfaces of your grill to protect it’s finish.
Page 20
Clean the ash from the Ash Tray of the grill periodically. If excessive ash is in the firepot, it may cause the fire to go out. This is especially true in the SMOKE setting. A shop vac is an excellent tool to use for removing the ash. WARNING: MAKE SURE THE GRILL FIRE IS OUT, THE UNIT IS OFF, UNPLUGGED AND COLD BEFORE ATTEMPTING TO CLEAN ASH FROM THE GRILL.
TROUBLESHOOTING CAUTION: Make sure the grill is completely cool and unplugged before you do any inspection, cleaning, maintenance or service work. Potential Problem Solution Cause Make sure the power cord is plugged Power in. Verify there is power at the electrical outlet.
Page 22
Pellets pellets. When contacting customer support Contact please have the following information Z GRILLS available: Your authorized Z Grills Customer dealer, your name, phone number, Get your new parts Service or your address, your Z Grill serial number and Z GRILLS part identification number.
DIGITAL THERMOSTAT CONTROL WIRING DIAGRAM Usage of the Meat Probe Put the plug of the Meat Probe into the control panel (PROBE1 or PROBE2) Insert the Probe into the food to measure the temperature The P1 temperature of the control panel is displayed as the temperature of PROBE1, while the P2 temp is displayed as the temp of PROBE2...
Thank you for purchasing a Z GRILL! If you have any question, please contact customer support or your Z GRILL dealer. Z GRILLS, INC. offers the best technical and sales support in the industry. When calling customer please be prepared to provide the following information: 1.Dealer's name and date of purchase...
Z GRILLS, Inc. shall not be liable if you install, operate, clean or maintain your grill without following the owners' manual instructions. Misuse, abuse, alteration and natural disasters...