Dexter Laundry T-350 Operators Manual Installation & Operation Instructions page 74

11 The drive size se ng has changed.
12 Washer controller internal error
13 The control cannot communicate with the drive
14 Over-current on the drive or motor.
15 Over-voltage on the drive or motor.
16 Overhea ng of the drive
17 Overload of the drive or motor
18 Ground Fault to the drive
19 Low Voltage to the drive
20 Internal drive error
21 Data error on communica ons between the
controller and drive
29 Drive Phase Loss
30 Internal Drive Error
(CE)
31 Drive Cer fica on Check Error
Table 7-17 Displayed OPL Washer Faults
8514-301-001 REV PR
Turn off the power to the washer. Check to ensure all the harnesses are properly connected to the
controller. Check to ensure the drive horsepower is proper for this size of washer. Turn on power to the
washer. (See Note) If problem reappears, contact your Dexter representa ve.
Turn off the power to the washer. Wait one minute. Turn on the power to the washer. (See Note) If
problem reappears, contact your Dexter representa ve.
Turn the power off to the washer. Check the data cable between the controller and the drive. If no
problem is observed, turn on power to the washer and test. (See Note) If problem reappears, contact
your Dexter representa ve.
Turn the power off to the washer. Check the washer motor to ensure it turns freely. Check the wiring
connec ons to the drive and motor. If no problem is observed, turn on power to the washer and test.
(See Note) If problem reappears, contact your Dexter representa ve.
Turn the power off to the washer. Check the washer motor to ensure it turns freely. Check the wiring
connec ons to the drive, braking resistors and motor. Measure incoming line voltage. If no problem is
observed, turn on power to the washer and test. (See Note) If problem reappears, contact your Dexter
representa ve.
Turn the power off to the washer. Allow the drive to cool. Check the cooling fins of the drive to ensure
proper airflow. Check the wiring to the drive including the fan wiring. If no problem is observed, turn
on power to the washer and test. (See Note) If problem reappears, contact your Dexter representa ve.
Turn the power off to the washer. Check the washer motor to ensure it turns freely. Check the wiring
connec ons to the drive and motor. If no problem is observed, turn on power to the washer and test.
(See Note) If problem reappears, contact your Dexter representa ve.
Turn the power off to the washer. Check the wiring connec ons to the drive and motor. Check the
ground wiring of the drive, motor and incoming connec on to ensure a proper ground is present. If no
problem is found, contact your Dexter representa ve.
Turn the power off to the washer. Check the wiring connec ons to the drive and motor. If no problem
is observed, turn on power to the washer and test. (See Note) Measure the incoming line voltage. If
problem reappears, contact your Dexter representa ve.
Turn the power off to the washer. Wait one minute. Turn the power on to the washer. (See Note) If
problem reappears, contact your Dexter representa ve.
Turn the power off to the washer. Check the data cable between the controller and the drive. If no
problem is observed, turn on power to the washer and test. (See Note) If problem reappears, contact
your Dexter representa ve.
Turn the power off to the washer. Check the wiring connec ons to the drive and motor. If no problem
is observed, turn on power to the washer and test. (See Note) Measure the incoming line voltage. If
problem reappears, contact your Dexter representa ve.
Turn the power off to the washer. Wait one minute. Turn the power on to the washer. (See Note) If
problem reappears, contact your Dexter representa ve.
Turn the power off to the washer. Wait one minute. Turn the power on to the washer. (See Note) If
problem reappears, contact your Dexter representa ve.
74