Dexter Laundry T300 Parts & Service Manual
  1. Manuals
  2. Brands
  3. Dexter Laundry Manuals
  4. Washer
  5. T-300 VENDED
  6. Parts & service manual

Dexter Laundry T300 Parts & Service Manual

Hide thumbs Also See for T300:
Table of Contents

Advertisement

Quick Links

USE THE BLUE TABS LOCATED ON THE
RIGHT AND LEFT SIDES OF THE FOLLOWING
DOCUMENT TO ADVANCE TO EACH SECTION.
8533-082-001 11/21

Advertisement

Table of Contents
loading

Related Manuals for Dexter Laundry T300

Summary of Contents for Dexter Laundry T300

  • Page 1 USE THE BLUE TABS LOCATED ON THE RIGHT AND LEFT SIDES OF THE FOLLOWING DOCUMENT TO ADVANCE TO EACH SECTION. 8533-082-001 11/21...
  • Page 2 6-Cycle OPL Washers T300, T400,T600 (100G) Caution! To reduce the risk of damage to the Water Inlet Valve, do not supply inlet water with a temperature that &...
  • Page 3 Equipment Safety Warnings, Symbols, and Indicates an imminently hazardous situation, Terminology Used in this Equipment which if not avoided, will result in death or seri- ous injury. Indicates a potentially hazardous situation, Warning! Do not operate equipment if door glass is which if not avoided could result in death or damaged in any way.
  • Page 4 WARNING WARNING • All washers must be installed in accordance to all applicable electrical, plumbing and all other local codes. Children should be supervised to ensure they do not operate or play • These installation and operation instructions are in or around equipment. for use by qualified personnel only.
  • Page 5 Warning! Do not operate equipment if door glass is Prohibited! Do not attempt to open, touch, or pro- damaged in any way. ceed before referring to the manual or unless quali- fied. Mandatory! Read all supporting documentation be- Warning! Keep clear of rotating parts. fore operating or maintaining equipment.

  • Page 6: Table Of Contents

    Dexter Safety Table of Contents Notes Guidelines Section 1: Machine Mounting & Installation WARNING T-300 ............14 T-350 & T-400 ..........15 T-450 & T-600 ..........16 T-300 Installation ...........17 These washers are equipped with devices and T-350 Installation ...........18 features relating to their safe operation. To avoid injury or electrical shock, do not perform T-400 Installation ...........19 and service, unless qualified to do so.
  • Page 7 Chassis and Drain Part # by Model ..106 & 107 Front Panel Removal ........50 Controls Transformer........62 Electrical Components - Back Panel Removal ........50 Main Relay Printed Circuit Board .....62 Top Compartment ...... 108 & 111 Drain Valve Access .........50 Power Connection Terminal Block ....62 Control Panel Part # by Model ...
  • Page 8 Specifications for below models are outlined in this book: T300 WN0300XA-10EV 120 volts 60hz. Single Phase T300 WN0300XA-12EV 208-240 volts 60hz. Single Phase or Three Phase T350 WN0350XA-12EV 208-240 volts 60hz Single Phase or Three Phase T400 WN0400XA-12EV 208-240 volts 60hz...
  • Page 9 T-450 Mounting Dimensions T-350 Mounting Dimensions T-400 Mounting Dimensions T-600 Mounting Dimensions 12 13/16” 27 1/8” 2 3/4” 29 7/8” 12 13/16” 36” 9 13/32” 2 3/4” Front 29 7/8” 9 13/32” Water Inlet Front Side Water Inlet Side Back Back 48”...
  • Page 10 T-350 Mounting Pad Dimensions T-300 Mounting Dimensions Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 11 T-400 Mounting Dimensions T-450 Mounting Pad Dimensions Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 12 T-600 Mounting Pad Dimensions Notes Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...

  • Page 13: Installation

    Installation & Operation All washers must be installed in accordance with all local, state and national building, electrical, and plumbing codes in effect in the area. Foundation Requirements The washer must be securely bolted to a substantial concrete floor, or mounted upon a suitable base which is in turn securely bolted to a substantial concrete floor.
  • Page 14 Liquid Chemical Connection Disconnect all power to the washer. Remove screw and lift out the cover located in the upper left corner of the machine (as viewed from the back). In the left rear corner of the washer is the chemical injection as- sembly.

  • Page 15: Detergent Measurements By Model

    Detergent Measurements Washer Operating Instructions By Washer Model Safety Door Lock This machine is equipped with a Safety Door Lock that locks the door closed from when the cycle is Use 1/4 started until the cycle is complete. The door lock prevents opening the door for up to 3 minutes if the power is interrupted during the cycle.
  • Page 16 TRANSIENT VOLTAGE SURGE SUPPRESSORS Notes Like most electrical equipment your new machine can be damaged or have its life shortened by voltage surges due to lightning strikes which are not covered by factory warranty. Local power distribution problems also can be detrimental to the life of electrical components. We recommend the installation of transient voltage surge suppressors for your new equipment.

  • Page 17: Machine Programming Instructions

    OPL Washer Cycle Parameter Ranges The range of each cycle parameter is shown below: Bath Cycle Time “ct” 0 to 15 minutes for Prewash, Rinse1 and Rinse 3 to 15 minutes for Wash and Final Rinse. For the baths that can, if the time is set to zero, then that bath will be eliminated from the cycle. Bath Water Temperature “t”...
  • Page 18 Cycle 1: Sheets and Pillowcases (Health Care) Cycle 4: Guest Laundry (Hotel / Motel / Healthcare) Bath Bath Cycle Water Water Delay Spin Injection Bath Bath Cycle Water Water Delay Spin Injection Time (min.) Temp. Level Fill Time (min.) Source Time (min) Temp.

  • Page 19: Rapid Advance Mode

    Washer Programming Instructions Rapid Advance Mode To enter the Rapid Advance mode, turn the key CCW. The Rapid Advance setting is not marked next to the key, but turning the CCW until it stops selects this mode. The Rapid Advance mode can be entered THERE ARE TWO WAYS TO MODIFY PROGRAMMING OF THE V-SERIES OPL SIX (6) from either the Idle mode or during the cycle.
  • Page 20 Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...

  • Page 21: Trouble Shooting

    Common Troubleshooting Solutions Symptom Probable Cause Suggested Remedy Machine Power Supply Check these areas: Circuit breakers, Voltage, Power leads, does not Power connections. Is front display LED showing a dollar start amount. Door Switch Check for continuity through door switch when door is closed.
  • Page 22 Common Troubleshooting Solutions Symptom Probable Cause Suggested Remedy Symptom Probable Cause Suggested Remedy Hot water Water Valve Coil Check coil continuity at terminals and replace if no continuity. Machine Check VFD by removing inspection panel and record any does not Check for 120 V power from main relay PCB does not numbers or letters displayed.

  • Page 23: Troubleshooting Machine Fault Errors

    Troubleshooting Machine Fault Errors Fault# Description Customer Action Displayed on front of washer Wrong washer size for drive Check VFD fault code before turning off power. If the type. controller was installed in a different size machine before being installed in this machine, a problem The following pages are a description of fault codes that will appear on the front of the can occur.
  • Page 24 Fault# Description Customer Action Fault# Description Customer Action Step 1: Make sure the cooling fins on the VFD heatsink The temperature sensor The variable frequency Check the data communication cable between the inside of the variable and the ventilation louvers on the VFD cooling fan cover drive (VFD) and the washer computer and the variable frequency drive are clean.

  • Page 25: Variable Frequency Drive Control Digital Readout Faults

    Variable Frequency Drive Control Fault# Description Customer Action VFD unit has been added or Soft reset control. Digital Readout Faults loose connection. Injection relay PCB has been Soft reset control. Fault# Description Customer Action added to machine or loose VFD received an illegal Reset drive.
  • Page 26 Variable Frequency Drive Control Digital Readout Faults Notes Fault# Description Customer Action OL or Overload of the drive or (Check drive fault code before powering down). Check motor the washer motor to ensure it turns freely. Check the wiring for loose connections to the drive and motor.

  • Page 27: Machine Service Procedures

    Top Panel Removal Step 1: Remove 4 screws that hold detergent dispenser to top panel. Step 2: Unlock top panel lock. Step 3: Raise top panel, slide to the rear to release from back clips and lift off. Front Panel Removal Step 1: Remove 2 screws between front panel top and front (located behind control panel).

  • Page 28: Air Gap

    Vacuum Breaker (also called an air gap) Door cam Flat blade screw on check position In the left rear of the cabinet is the vacuum breaker. It guides the water to the tub and dispenser and prevents door switch latching a back flow of water.

  • Page 29: Adjusting The Loading Door

    Loading Door Disassembly Adjusting the Loading Door The door can be adjusted by changing the number of shims behind the door hinge and the door lock Step 1: Remove the loading Step 2: While holding down on Step 3: Work all the way around door as outlined above.

  • Page 30: Outer Cabinet Removal

    Outer Cabinet Removal T-300, T350, T-400, T450, T-600 Door Locking Gear Motor Assembly Removal of Cabinet T-300, T-400, T-600 The door locking gear motor is rotated shut with Step 1: The power supply, water hoses, and drain connection must all be disconnected before proceeding control voltage to lock the door and releases when with the disassembly.

  • Page 31: Tub Back, Bearing And Cylinder Assembly

    Tub Back, Bearing and Cylinder Assembly Basket assembly T-300, T-350, T-400, T450, T-600 Basket Pulley, Bearing Housing, Water Seals and Tub Back The cast iron basket pulley is retained by a bolt, locking washer and a flat washer. Removal Removal Reassembly Reverse the procedures to the left Step 1: Insert a large screw driver or punch through a spoke in the pulley...

  • Page 32: Drive Motor Removal

    Reassembly Step 1: When installing new bearings into a bearing housing, first press T-300 Bolt Torque Chart the front (large) bearing into the housing until it bottoms. With the NUMBER bearing spacer in place, press the rear bearing in until the spacer is Bolt Size Where Used Torque...

  • Page 33: Control Mounting Trough

    Control Mounting Trough Remove top panel to access control trough. (see Removing Top Panel) It sets on the right side of the machine and holds the control PCB’s, transformers,and pressure switch. Main Data Communication Cable Goes between front PCB board and Variable Frequency Drive unit mounted center rear of machine. It has telephone type connectors at each end and is inserted at Controller PCB and the Variable Frequency Drive.

  • Page 34: Pressure Switch

    Pressure Switch Caution (Not recommended by Factory!) Changing Factory preset adjustment voids all factory water usage specifications. Pressure Sensor Electronic The pressure switch sets the water level in the washer. As the water level rises, it compresses the air in the pressure switch hose.

  • Page 35: Delta Variable Frequency Drive

    Water Level Chart   Power Connection Terminal Block         This terminal block sets at the very back of the control trough. Incoming power to the washer should   connect here. (see Electrical under Installation and Operation Section for exact connections) ...
  • Page 36 MAXIMUM SPIN SPEED ADJUSTMENT: Notes If desired, the washer can be adjusted to limit the maximum extract spin speed for all wash cycles. To make this adjustment, a jumper wire must either be installed or removed on the Variable Frequency ...

  • Page 37: Start Circuit

    Electrical Path Circuit Schematics Start Circuit Power travels into the machine on L1 & L2 & (L3) ( if 3 phase used). 208- 240VAC goes to a Control Transformer ( must be checked at start -up to coincide with machine operating voltage) that steps the voltage down to 115VAC for the controls.

  • Page 38: Wash Circuit

    T-300-10 Schematic Wash Circuit As the washer fills the tub through the back of the machine with either one or both the C1 Cold and H1 Hot Water Valves, the Wash Basket will tumble one direction for 12 seconds, pause, and then reverse di- rection for 12 seconds.
  • Page 39 T-300-10 Diagram T-300-10 V4 Schematic Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 40 T-300-12 Schematic T-300-10 V4 Diagram Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 41 T-300-12 V4 Schematic T-300-12 Diagram Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 42 T-350-12 Schematic T-300-12 V4 Diagram Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 43 T-350-12 Diagram T-350-12 V4 Schematic Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 44 T-350-12 V4 Diagram T-400-12 Schematic Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 45 T-400-12 Diagram T-400-12 V4 Schematic Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 46 T-400-12 V4 Diagram T-450-12 Schematic Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 47 T-450-12 Diagram T-450-12 V4 Schematic Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 48 T-450-12 V4 Diagram T-600-12 Schematic Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 49 T-600-12 Diagram T-600-12 V4 Schematic Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 50 T-600-12 V4 Diagram Notes Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 51 Notes Notes Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 52 Notes C-Series Accessories T300 WN0300XA-10EV 120 volts 60hz. Single Phase T300 WN0300XA-12EV 208-240 volts 60hz. Single Phase or Three Phase T350 WN0350XA-12EV 208-240 volts 60hz Single Phase or Three Phase T400 WN0400XA-12EV 208-240 volts 60hz Single Phase or Three Phase...

  • Page 53: Parts Data

    8636-018-001 8636-018-001 8636-018-001 8636-018-001 8636-018-001 Parts Data: Door Glass Gasket 9206-411-002 9206-411-002 9206-411-002 9206-411-002 9206-411-002 T300 WN0300XA-10EV 120 volts 60hz. Single Phase T300 WN0300XA-12EV 208-240 volts 60hz. Single Phase or Three Phase T350 WN0350XA-12EV 208-240 volts 60hz Single Phase or Three Phase...
  • Page 54 Wiring Harness Part # by Model Notes Description T-300 T-350 T-400 T-450 T-600 Wiring Harness (Add Bleach Lite 9794-001-001 9794-001-001 9794-001-001 9794-001-001 9794-001-001 assy included) Wiring Harness, Door Lock 9627-791-003 9627-791-003 9627-791-003 9627-791-003 9627-791-004 Wiring Harness, 9627-796-001 9627-796-001 9627-796-001 9627-796-001 9627-796-002 Drain,Thermo,DoorSol Data Cable...
  • Page 55 Cabinet and Front Panel Group Part # by Model Description T-300 T-350 T-400 T-450 T-600 Panel, Side (Left or Right) - 9732-359-006 9732-359-007 9732-359-008 stainless Panel, Right Side-stainless 9989-639-001 9989-640-001 Panel, Left Side - stainless 9989-639-002 9989-640-002 Screw, (Side Panel to Base) 9545-018-018 9545-018-018 9545-018-013...
  • Page 56 Cabinet and Front Panel Group Part # by Model Continued Notes 23,24 Description T-300 T-350 T-400 T-450 T-600 Panel Top, Assembly (includes 9989-498-001 9989-498-002 9989-498-003 9989-498-004 9989-498-005 catch) Catch, Top Panel 9086-017-001 9086-017-001 9086-017-001 9086-017-001 9086-017-001 Rivit-Catch, Top Panel 8638-190-009 8638-190-009 8638-190-009 8638-190-009...

  • Page 57: Rear View Access Part # By Model

    Rear View Access Part # by Model Description T-300 T-350 T-400 T-450 T-600 Drive Motor, 3 Phase (Inverter 9732-225-001 9732-227-001 9732-127-012 9732-127-014 9732-127-012 duty) W/Pulley Pulley, Motor 9453-169-012 9453-169-012 9453-170-003 9453-181-001 9453-170-003 Set Screw,Sq.Hd(motor pulley) 9545-028-015 9545-028-015 9545-028-015 9545-028-015 9545-028-015 Rod, Motor Mtg 9497-222-002 9497-222-002...
  • Page 58 0935-135-002 0935-135-002 0935-135-002 0935-135-002 Screw-#10Bx1/2 9545-008-026 9545-008-026 9545-008-026 9545-008-026 9545-008-026 Screw, 10Bx1/2 9545-008-026 9545-008-026 9545-008-026 9545-008-026 9545-008-026 Wire Assy -Violet, (24” T300-10) 8220-118-001 Cap-Injector Assy 0935-127-001 0935-127-001 0935-127-001 0935-127-001 Wire Assy, Jumper 8220-117-002 8220-117-002 8220-117-002 8220-117-002 8220-117-002 Clamp 9242-117-014 9242-117-014...
  • Page 59 Cylinder, Seals & Bearings Part # by Model Description T-300 T-350 T-400 T-450 T-600 Bearing and Seal Kit 9732-219-001 9732-219-008 9732-219-003 9732-219-005 9732-219-005 Housing, Bearing- Assembly (items #2-#6) 9803-182-001 9803-179-003 9803-179-002 9803-186-001 9803-186-001 Housing, Bearing 9241-174-002 9241-169-002 9241-169-002 9241-180-002 9241-180-002 Bearing, Front (LARGE) 9036-159-001 9036-159-009...
  • Page 60 Door Lock Assembly (All Models) Gear Motor Door Lock Assembly Description T300 T350 T400 T450 T600 Actuator Assembly (Includes 9892-015-001 9892-015-001 9892-015-001 9892-015-001 9892-015-001 1-10, Rod NOT included) Bracket Assy, Slide Lock Actuator 9985-190-001 9985-190-001 9985-190-001 9985-190-001 9985-190-001 Key Description...

  • Page 61: Loading Door Part # By Model

    Loading Door Part # by Model Description T300 T350 T400 T450 T600 Loading Door, Complete #1-10 9960-308-001 9960-308-001 9960-309-001 9960-309-001 9960-309-001 Loading Door, Ring 9487-264-002 9487-264-002 9487-265-002 9487-265-002 9487-265-002 Gasket, Loading Door 9206-411-002 9206-411-002 9206-419-001 9206-419-001 9206-419-001 Window, Loading Door...

  • Page 62: Water Inlet Valve Breakdown Part # By Model

    Water Inlet Valve Breakdown Part # by Model Loading Door Hinge 180 Degree Opening Description T300 T350 T400 T450 T600 Door Hinge Assembly (mounts to tub 9955-030-001 9955-030-001 9955-030-001 9955-030-001 9955-030-001 front) Shim, Loading Door Hinge (Thin) 9552-036-001 9552-036-001 9552-036-001...

  • Page 63: Water Inlet Part # By Model

    Water Inlet Part # by Model Description T-300 T-350 T-400 T-450 T-600 Clamps Valve, Water Inlet (dual outlet) 9379-183-012 9379-183-012 9379-183-012 9379-183-012 9379-183-012 (see Water Inlet Valve Break- down for individual parts) Screw, Valve Mtg 9545-008-026 9545-008-026 9545-008-026 9545-008-026 9545-008-026 Vacuum Breaker 9610-001-001 9610-001-001...

  • Page 64: Drain Valve Group Part # By Model

    Drain Valve Group Part # by Model Notes Description T300 T350 T400 T450 T600 Valve, Drain (includes #2 thru 9379-199-001 9379-199-001 9379-202-001 9379-202-001 9379-202-001 #11) Body, Valve (w/ball) 9064-068-002 9064-068-002 9064-070-001 9064-070-001 9064-070-001 Motor & Gear Train (complete) 9914-137-020 9914-137-020...

  • Page 65: Chassis And Drain Part # By Model

    Nut, Hex 5/8-11 8640-425-001 8640-425-001 Shim, Support Assembly (thin) 9552-038-003 9552-038-003 9552-038-003 9552-038-001 9552-038-001 Injection Tube 9883-006-001 9883-010-001 9883-007-001 Hose-Inlet, Water (T300 & T350, 9242-458-001 9242-458-001 Between Vacume Breaker and tub) Dispenser Soap 9122-005-004 9122-005-004 9122-005-004 9122-005-004 9122-005-004 Gasket, Dispenser 9206-416-001...

  • Page 66: Electrical Components - Top Compartment

    Electrical Components - Top Compartment 208/240VAC Electrical Components - Top Compartment Description T300 T350 T-400 T-450 T-600 Mechinical Pressure Switch Trough Assy,Controls 208-240 9857-210-002 9857-211-001 9857-212-001 9857-213-001 9857-214-001 volt (all parts below #2-#43 & trough) Trough only 9839-018-001 9839-018-001 9839-018-001...
  • Page 67 Electrical Components Cont.- Top Compartment 120VAC Description T300 120V Trough Assy,Controls 120 Volt (all parts below #2-#43 & trough) 9857-210-001 Trough only 9839-018-001 Screw, Trough Sides 9545-008-026 Lockwasher #10 8641-582-006 Angle Support Trough 9003-337-001 Screw, Trough Bracket 9545-008-026 Cord Assembly-Service 9802-037-009 Wire Assembly, Red, 29”...

  • Page 68: Control Panel Part # By Model

    Control Panel Part # by Model Description T-300 T-350 T-400 T-450 T-600 Panel Control Assembly(panel 9989-477-001 9989-477-001 9989-478-001 9989-478-001 9989-479-001 only) Screw, Hxwshrhdundct #10Bx 9545-008-026 9545-008-026 9545-008-026 9545-008-026 9545-008-026 1/2” (Control to sides) Plate-Latch, Top 9452-625-001 9452-625-001 9452-625-001 9452-625-001 9452-625-001 Nut, #8-32 8640-412-005 8640-412-005...
  • Page 69 Labels and Diagrams All WCVD Models Notes Description T-300 T-350 T-400 T-450 T-600 Operators Manual 8514-236-001 8514-236-001 8514-238-001 8514-239-001 8514-240-001 Instructions Spin Direction 8507-275-001 8507-275-001 8507-275-001 8507-275-001 8507-275-001 Wiring Schematic & Diagram, 9506-549-001 (120 VAC) Wiring Schematic & Diagram 9506-550-001 9506-552-001 9506-552-001 9506-552-001...

  • Page 70: Parts

    Notes Section 9: Parts 50Hz Models: Parts in this section used only in these models. All other parts are same as standard 60 Hz pages. Wiring Diagrams & Schematics Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 71 Transformer, Electrical -39 models Water Valve, Drain Valve -39 models Key Component T-300 T-350 T-400 T-450 T-600 T-300 T-350 T-400 T-450 T-600 Key Component Operators Manual 8514-236-002 8514-237-002 8514-238-002 8514-239-002 8514-240-002 Water Valve 9379-183-013 9379-183-013 9379-183-013 9379-183-013 9379-183-013 Wiring Schematic & 9506-551-001 9506-553-001 9506-553-001...
  • Page 72 Gear Motor Door Lock Assembly 24V AC Notes Description T-300 T-350 T-400 T-450 T-600 Actuator Assembly (Includes 1-10, 9892-015-002 9892-015-002 9892-015-002 9892-015-002 9892-015-002 Rod NOT included) Bracket Assy, Slide Lock Actuator 9985-190-001 9985-190-001 9985-190-001 9985-190-001 9985-190-001 Bracket Assy, Slide - Unlock 9985-189-001 9985-189-001 9985-189-001...
  • Page 73 T-300-39 Schematic T-300-39 Diagram Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 74 T-300-39 V4 Schematic T-300-39 V4 Diagram Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 75 T-350-39 Schematic T-350-39 Diagram Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 76 T-350-39 V4 Schematic T-350-39 V4 Diagram Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 77 T-400-39 Schematic T-400-39 Diagram Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 78 T-400-39 V4 Schematic T-400-39 V4 Diagram Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 79 T-450-39 Schematic T-450-39 Diagram Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 80 T-450-39 V4 Schematic T-450-39 V4 Diagram Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 81 T-600-39 Schematic T-600-39 Diagram Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...
  • Page 82 T-600-39 V4 Schematic T-600-39 V4 Diagram Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...

  • Page 83: Maintenance

    Notes Section 10: Maintenance Part # 8533-082-001 11/21 Part # 8533-082-001 11/21...

  • Page 84: Preventative Maintenance

    Preventative Maintenance Daily Step 1: Check that the loading door remains securely locked and cannot be opened during an entire cycle. Step 2: Clean the top, front, and sides of the cabinet to remove residue. Step 3: Clean the soap dispenser and lid and check that all dispenser mounting screws are in-place and tight.

This manual is also suitable for:

T400T600T350T450

Table of Contents