English CONTENTS GENERAL POWER TOOL SAFETY WARNINGS ........18 PRECAUTIONS FOR CORDLESS IMPACT DRIVER ........21 CAUTION ON LITHIUM-ION BATTERY ............22 REGARDING LITHIUM-ION BATTERY TRANSPORTATION ...... 23 SYMBOL ....................... 23 SPECIFICATIONS ..................24 STANDARD ACCESSORIES ............... 25 OPTIONAL ACCESSORIES (sold separately)..........25 APPLICATIONS ....................
Page 19
English b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Page 20
English b) Do not use the power tool if the switch does not turn it on and off . Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools.
English CAUTION Keep children and infi rm persons away. When not in use, tools should be stored out of reach of children and infi rm persons. PRECAUTIONS FOR CORDLESS IMPACT DRIVER Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring.
English CAUTION ON LITHIUM-ION BATTERY To extend the lifetime, the lithium-ion battery equips with the protection function to stop the output. In the cases of 1 to 3 described below, when using this product, even if you are pulling the switch, the motor may stop. This is not the trouble but the result of protection function.
English If liquid leaks onto your skin or clothes, wash well with clean water such as tap water immediately. There is a possibility that this can cause skin irritation. If you fi nd rust, foul odor, overheating, discolor, deformation, and/or other irregularities when using the battery for the fi...
English SPECIFICATIONS POWER TOOL Model WH14DJL WH18DJL Voltage 14.4 V 18 V No-load speed 0 – 2600 /min 0 – 2400 /min Capacity M6 – M14 (Ordinary bolt) Tightening torque 140 N . m 145 N . m (Maximum) BSL1415S: BSL1425: BSL1430: BSL1815S:...
English STANDARD ACCESSORIES In addition to the main unit (1 unit), the package contains the accessories listed in the below. WH18DJL WH14DJL Charger (UC18YKSL or UC18YFSL) UC18YKSL UC18YFSL Battery (BSL1815S or BSL1815 or — BSL1815S BSL1830 BSL1825 or BSL1830) BSL1815 BSL1825 Battery (BSL1415S or BSL1425 or...
English BATTERY REMOVAL/INSTALLATION Handle Battery removal Hold the handle tightly and push the battery latch to Pull out Latch remove the battery (see Fig. 3). CAUTION Never short-circuit the battery. Push Battery installation Insert the battery while observing its polarities (see Battery Fig.
Page 27
English Table 1 Indications of the pilot lamp Lights for 0.5 seconds. Does not light Before Blinks for 0.5 seconds. (off for 0.5 seconds) charging While Lights continuously Lights charging Lights for 0.5 seconds. Does not light Charging Pilot Blinks for 0.5 seconds.
English Hold the charger fi rmly and pull out the battery NOTE After charging, pull out batteries from the charger fi rst, and then keep the batteries properly. Regarding electric discharge in case of new batteries, etc. As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated, the electric discharge might be low when using them the fi...
English HOW TO USE Movement Installing the bit Guide sleeve Always follow the following procedure to install driver bit. (Fig. 5) Pull the guide sleeve forward. Insert the bit into the hexagonal hole in the socket. Driver bit Release the guide sleeve and it returns to its original Hexagonal hole in the anvil position.
English CAUTION Applying the impact driver for too long tightens the screw too much and can break Tightening a screw with the impact driver at an angle to that screw can damage the head of the screw and the proper force will not be transmitted to the screw. Tighten with this impact driver lined up straight with the screw.
English NOTE Do not touch the metal parts, as it gets very hot during continuous work. Cautions on use of the speed control switch This switch has a built-in, electronic circuit which steplessly varies the rotation speed. Consequently, when the switch trigger is pulled only slightly (low speed rotation) and the motor is stopped while continuously driving in screws, the components of the electronic circuit parts may overheat and be damaged.
Page 32
Repair, modifi cation and inspection of HiKOKI Power Tools must be carried out by a HiKOKI Authorized Service Center. This Parts List will be helpful if presented with the tool to the HiKOKI Authorized Service Center when requesting repair or other maintenance.
English SERVICE PARTS LIST UC18YFSL UC18YKSL 26 27 BSL1415S BSL1425 BSL1430 BSL1815S BSL1815 BSL1825 BSL1830...
Page 34
English Item Item Part Name Q’TY Part Name Q’TY RETAINING RING TAPPING SCREW (W/FLANGE) D3X16 WASHER(D) 37 NAME PLATE GUIDE SPRING (D) 38 BATTERY GUIDE SLEEVE (D) 501 CHARGER FRONT CAP 502 BATTERY COVER TAPPING SCREW (W/SP. WASHER) D4X25 503 CASE HAMMER CASE WASHER (F) STEEL BALL D3.5...