Related Manuals for MSA SMC 5100-99-IT
Summary of Contents for MSA SMC 5100-99-IT
- Page 1 Operating Manual SMC 5100-99-IT Transmitter Document No./Revision:T12005/B2 Print Spec: 10000005389 (F) MSAsafety.com...
- Page 2 The warranties made by MSA with respect to the product are voided if the product is not installed and used in accordance with the instructions in this manual. Please protect yourself and your employees by following the instructions.
-
Page 3: Table Of Contents
3.2.4 Sentry Operation Using Sentry Connection 3.2.5 General Enclosure Installation Transmitter Installation Module Address Switch Operation Introduction Data Entry Keypad Main Menu Set-Up 4.4.1 Alarms 4.4.2 Relays 4.4.3 Range 4.4.4 4-20mA 4.4.5 RS-485 4.4.6 DigInput Maintenance Sub-Menu Service SMC 5100-99-IT Transmitter... - Page 4 5.5.5 Display Shows “H” or “L” 5.5.6 Display Shows “C” – Calibration Mode 5.5.7 Display Shows “S” – Sentry Connection 5.5.8 Diagnostic LEDs 5.5.9 Error Messages Specifications Model Numbers & Spare Parts Limited Warranty Modbus Memory Map SMC 5100-99-IT Transmitter...
-
Page 5: Product Description
• Integral alphanumeric LED display • Optional integral alarm relays • Analog 4-20 mA input/output ® • Modbus RTU interface NOTE: Modbus is a registered trademark of Schneider Electric • SMC Sentry interface • 316 Stainless steel enclosure option SMC 5100-99-IT Transmitter... -
Page 6: Product Configuration
Low Alarm relays and SPDT, 250VAC, 0.25 Amp for the Trouble relay. If the gas sensor module is provided with the optional relays, it will include Terminal P4 on the interface board (Section Module Address Switch). Relay output connections are on P4. SMC 5100-99-IT Transmitter... -
Page 7: Mechanical
316 Stainless Steel enclosure. Both enclosure covers have a viewing window. The design of the enclosure allows 3-way mounting choices as shown below. NOTE: Module installation must be such that it is mounted vertically with sensor pointing downward. Model 5100-99-IT-S1/S2 Toxic Gas Sensor – Stainless Steel Enclosure, Dimensions SMC 5100-99-IT Transmitter... -
Page 8: Transmitter Electronics
Power Requirements The modules operate on 24 VDC power between 10 VDC and 30 VDC. Filtered, regulated DC power must be supplied from a separate source or from an approved Sentry or IT controller. SMC 5100-99-IT Transmitter... -
Page 9: Cautions & Warnings
• Relays are not to be used for safety critical functions. NOTE: Installation and wiring must be in accordance with the National Electrical Code. Voltage AC conductors are not to be run in the same conduit as voltage DC conductors. SMC 5100-99-IT Transmitter... -
Page 10: Installation
TX A and TX B lines. The IT series of toxic gas sensors automatically apply the bias jumpers, and are factory installed so that the bias is always enabled. SMC 5100-99-IT Transmitter... -
Page 11: Sentry Operation Using Sentry Connection
3. For hazardous locations an Explosion poof seal fitting must be installed within 18" of the transmitter. NOTE: When enclosure earth grounding is required for the installation a grounding lug is located in the base of the enclosure. Install the earth ground under the green ground screw. SMC 5100-99-IT Transmitter... -
Page 12: Transmitter Installation
* P4 Connections are installed only when the optional Relays are included ** Trouble relay is a fail-safe so it is energized for normal operation, functions are labeled for normal operation. NOTE: The starting delay is normally approx. 3 minutes but in some circumstances may take longer. SMC 5100-99-IT Transmitter... -
Page 13: Module Address Switch
NOTE: Use selector switch to pick Sentry PSG addresses 1 through 8 only. If using Modbus output sensor addresses 1-15 are available. Position 0 allows the Modbus Address to be set by software menu, in the range 16-254. SMC 5100-99-IT Transmitter... - Page 14 3 Installation Interface Board Connectors RS-485 – Termination, BIAS Jumper SMC 5100-99-IT Transmitter...
- Page 15 3 Installation Analog Output Circuit Types SMC 5100-99-IT Transmitter...
- Page 16 3 Installation Analog Output, 4-20 mA Circuit Type Connections for 5100-99-IT SMC 5100-99-IT Transmitter...
- Page 17 3 Installation Analog Input Connection Options for 5100-99-IT SMC 5100-99-IT Transmitter...
- Page 18 3 Installation Wiring Connections for Modbus and Sentry PSG Interface 5100-XX-IT TO MODBUS DEVICE SMC 5100-99-IT Transmitter...
- Page 19 3 Installation Wiring Connections for Remote Alarm Reset 5100-XX-IT Remote Alarm Reset (Unsupervised) (dry contact only unpowered) 5100-XX-IT Remote Alarm Reset (Supervised) SMC 5100-99-IT Transmitter...
-
Page 20: Operation
Each switch functions as if it is a manually activated panel key. The keys are located under the faceplate above and below the LED display and are labeled M , E , ▲ and ▼ as shown below. SMC 5100-99-IT Transmitter... -
Page 21: Main Menu
Description STARTING Delay from loss of power at start-up XXX PPM Concentration LXXX PPM Low Alarm (Warning) HXXX PPM High Alarm (Alarm) HIGH Measures gas, concentration exceeds 100% of Full Scale CXXX PPM Calibration Mode Acknowledged Function SMC 5100-99-IT Transmitter... -
Page 22: Set-Up
5100-06-IT Chlorine IN 10 5100-10-IT Sulfur Dioxide IN 12 5100-12-IT Nitrogen Dioxide IN 21 5100-21-IT Hydrogen Chloride IN 25 5100-25-IT Ammonia IN 26 5100-26-IT Hydrogen Fluoride %LEL 0-100% LEL %VOL 0-100% Volume 0-100 PPM % Full Scale 0-20mA SMC 5100-99-IT Transmitter... -
Page 23: Rs-485
Down 4-20mA S.P. Function - 4-20 mA Adjust * D Below Down RS-485 S.P. Function - RS-485/Sentry Output Adjust * E Below Select between supervised (Sprvsd) or unsupervised (UnSprvd) mode for Down Dig Input the Digital Input. SMC 5100-99-IT Transmitter... - Page 24 S.P. Function - User Selectable mA Value Enter *T1.50mA Use ▲ or ▼ keys to select mA Value between 0.5 and 3.7mA Enter *T1.50mA Select 1.5 mA value during trouble RS-485 Adjustment Example Enter Address S.P. Function - RS-485 Address Adjust SMC 5100-99-IT Transmitter...
- Page 25 S.P. Function - RS-485 Address Adjust Down Baud S.P. Function - RS-485 Baud Rate Adjust Enter *38400 Press [E] to select or ▲ or ▼ to select another NOTE: The Key is the same as the function. Mode=M, Enter=E, Up=▲, and Down=▼. SMC 5100-99-IT Transmitter...
-
Page 26: Maintenance Sub-Menu
4 Operation Maintenance Sub-Menu The maintenance menu enables the operator to view sensor and software versions. MSA Safety technical support has access to other values as needed. The maintenance menu operation is described in the table below. Function Display Description... - Page 27 5) Extender Type (Interface Card Type) 6) 5V supply voltage status *** ClearMem will restore the transmitter to its factory configuration. The user will have to reconfigure it as 5100-99-IT by following the SetUp / 4-20 mA / Mode procedure (Section Set-Up). SMC 5100-99-IT Transmitter...
-
Page 28: Service
• Model 5311-02 rain shield is recommended for installation in wet areas. 5.4.3 Standard Voltages • Regulated DC voltage to be applied to the sensor module must be between 10 VDC and 30 VDC. SMC 5100-99-IT Transmitter... -
Page 29: Inspection And Troubleshooting Guide
5.5.6 Display Shows “C” – Calibration Mode Complete calibration and exit to operating mode. 5.5.7 Display Shows “S” – Sentry Connection Check connections with Sentry Controller 5.5.8 Diagnostic LEDs 1 = 1 Hz Heartbeat normal, 2 Hz Panic Error SMC 5100-99-IT Transmitter... -
Page 30: Error Messages
SNS TBL Forced Trouble (Test Condition) Err: 400 SNS LOW Very low sensor output - down indicator Err: 800 SNS LOW Very low sensor output (<5% for Oxygen sensor) COM SNSR SNS FAIL Internal sensor communication error SMC 5100-99-IT Transmitter... -
Page 31: Specifications
(SS) 7.6 x 4.4 x 4.9 in. (19.3 x 11.2 x 12.4 cm) (AL) 3.4 lb. (1.5 Kg) Weight (SS) 7.2 lb. (3.3 Kg) Warranty Limited Warranty 2 years Specifications subject to change without notice NOTE: Relays are not to be used for safety related functions. SMC 5100-99-IT Transmitter... -
Page 32: Model Numbers & Spare Parts
Model Numbers & Spare Parts Model Numbers 5100-99-IT-AL-01 4-20mA Transmitter, AL 5100-99-IT-AL-02 4-20mA Transmitter, Relay, AL 5100-99-IT-SS-01 4-20mA Transmitter, SS 5100-99-IT-SS-02 4-20mA Transmitter, Relay, SS Spare Parts SPL21945 Transmitter SPL21825 Interface Board without Relay SPL21829 Interface Board with Relay SMC 5100-99-IT Transmitter... -
Page 33: Limited Warranty
Limited Warranty MSA Safety warrants its products to be free from defects in workmanship or material under normal use and service for two years after date of shipment. MSA Safety will repair or replace without charge any equipment found to be defective during the warranty period. -
Page 34: Modbus Memory Map
9 Modbus Memory Map Modbus Memory Map SMC 5100-99-IT Transmitter...