Table of Contents
Advertisement
1 1
Product Specific and Important Safety Information
A. Appliance Certification
MODEL:
P42i-TC Pellet Insert
LABORATORY: PFS • TECO
REPORT NO.
F22-858
TYPE:
Pellet Fueled Insert/Supplementary
For Residential Use
STANDARD(s):
ASTM E2779, ASTM E2515, ASTM
E1509, ULC-S628
ELECTRICAL
120 VAC, 60 Hz, Start 4.2 Amps, Run
RATING:
2.8 Amps
GLASS
5mm mirrored ceramic glass
SPECIFICATION:
The P42i-TC Pellet Insert is certified to
comply with 2020 EPA particulate emission
standards.
NOTE: This installation must conform to local codes. In the
absence of local codes you must comply with the
E1509, ULC-S628
& (UM) 84-HUD
B. Manufactured Home Approved
This appliance is approved for manufactured home
installations when not installed in a sleeping room and when
an outside combustion air inlet is provided.
The structural integrity of the manufactured home floor,
ceiling, and walls must be maintained. The appliance must
be properly grounded to the frame of the manufactured home
and use only listed pellet vent, Class "PL" connector pipe.
A Harman® Outside Air Kit must be installed in a manufactured
home installation.
T H E S T R U C T U R A L I N T E G R I T Y O F T H E
MANUFACTURED HOME FLOOR, WALL, AND CEILING/
ROOF MUST BE MAINTAINED.
DO NOT INSTALL IN SLEEPING ROOM.
Risk of Fire! Hearth & Home Technologies disclaims any
responsibility for, and the warranty and agency listing will
be voided by the below actions.
This wood heater needs periodic inspection and repair for
proper operation. It is against federal regulations to operate
this wood heater in a manner inconsistent with operating
instructions in this manual.
4
CAUTION
WARNING
Harman® • P42i Owner's Manual • 2023 -___ • 03/23
C. BTU & Efficiency Specifications
EPA Certification Number:
EPA Certified Emissions:
*LHV Tested Efficiency:
**HHV Tested Efficiency:
***EPA BTU Output:
****BTU Input
Vent Size:
Hopper Capacity:
Fuel
* Weighted average LHV efficiency using data collected
during EPA emissions test.
**Weighted average HHV efficiency using data collected
during EPA emissions test.
***A range of BTU outputs based on EPA Default Efficiency
and the burn rates from the low and high EPA tests.
****Based on the maximum feed rate per hour multiplied by
approximately 8600 BTU's which is the average BTU's from
ASTM
a pound of pellets.
This wood heater has a manufacturer-set minimum low burn
rate that must not be altered. It is against federal regulations
to alter this setting or otherwise operate this wood heater
in a manner inconsistent with operating instructions in this
manual.
This wood heater needs periodic inspection and repair for
proper operation. It is against federal regulations to operate
this wood heater in a manner inconsistent with operating
instructions in this manual.
DO NOT:
• Install or operate damaged appliance
• Modify appliance
• Install other than as instructed by Hearth & Home
Technologies
• Operate the appliance without fully assembling all
components
• Overfire
• Install any component not approved by Hearth &
Home Technologies
• Install parts or components not listed or approved.
• Disable safety switches
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
For assistance or additional information, consult a qualified
installer, service agency or your dealer.
NOTE: Hearth & Home Technologies, manufacturer of
this appliance, reserves the right to alter its products, their
specifications and/or price without notice.
Harman
is a registered trademark of Hearth & Home
®
Technologies.
F22-858
1.0 g/hr
84%
79%
5,637 - 32,782
7,400 – 41,800
4 Inch
64.5 lbs
Wood Pellet
8742-900A
Advertisement
Table of Contents
