Cardin Elettronica SLi324 Manual page 14

INSTRUCTIONS FOR USE
• This device has been created to be integrated into the structure of specially made
sliding gates. The geared motor is fitted with screw type attachments that allow it
to be fitted inside metal profiles.
ASSEMBLY PROCEDURE
The unit may be positioned either to the right or to the left of the passageway.
Respect the following limits:
- SLi324: max. weight 300 kg
The builder must make sure that the closing system respects the technical indications
supplied by the standards and laws in force:
- Opening and closing direction mechanical stops;
- Safety devices;
- Correct risk analysis at possible crushing points etc.
See: www.cardin.it - archives - Installation guide and approvals certificates -
s reserved. Unauthorised copying or use of the information contained in this document is punishable by law
MANUAL RELEASE MECHANISM
Caution! Never carry out the release/rearming procedure when
the gate is moving. Make sure that the power is switched off at
the mains before releasing or rearming the motor.
RELEASE SYSTEM ACCESS
An access slot will have to be built into the column for the release mechanism.
REMOVABLE DRIVE SHAFT
The drive shaft is removable to allow rapid installation and to facilitate the precise
positioning of the geared motor.
ELECTRONIC PROGRAMMER
Description :
umber :
DI0609
Electronic control unit for two dc motor with an incorporated encoder and radio
AUTOMAZIONE INTEGRATO PER CANCELLI
receiver card, which allows the memorisation of 300 user codes. The "rolling code"
ode : 205/BLi824
type decoder uses 433.92 MHz series transmitters S449.
A BATTENTE
Heath Date: 17-07-2014
The motor rotation speed is electronically controlled, starting slowly and increasing
ETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831 in speed; the speed is reduced as it nears the travel limit so as to enable a controlled
smooth stop. Programming is carried out using the buttons P1, P2, P3, and allows
you to set the system, the current sensor and the entire gate travel distance. The logic
carries out position control using an encoder. The intervention of the anticrush/antidrag
sensor during the closing and opening stages causes travel direction inversion.
The geared motor is fitted with an Allen
key operated manual release system.
The geared motor can be released by
rotating the hexagonal socket clock-
wise and the automatic resetting of the
gears is obtained by rotating the socket
anti-clockwise.
In both cases it is sufficient to rotate
the socket to the end of its natural
course making sure that you do not
force it (about 3 rotations).
50
Manual release system
activated via a 5 mm hex-
agonal socket (Allen key 5)
5
IMPORTANT REMARKS
In conformity with the electrical safety standards it is forbidden to connect
binding posts 9 and 10 directly to a circuit that receives power greater
than 30 Vac/dc.
Warning! For the correct operation of the programmer the incorporated
batteries must be in good condition.
The programmer will lose the position of the gate in case of blackouts
when the batteries are flat the alarm will sound.
Check the good working order of the batteries every six months (see
page 21 "Battery check").
• After having installed the device, and before powering up the
programmer, release the door (manual release mechanism) and move
it manually, checking that it moves smoothly and has no unusual points
of resistance.
• The controlled load output (binding post 15) is aimed at reducing
battery power consumption (if installed) during blackouts; photocells and
other safety devices should be connected to this output.
• When a command is received, via radio or via wire, the electronic
programmer routes voltage to the CTRL 24 Vdc output. It then evaluates
the state of the safety devices and if they are at rest it will activate the
motor.
• Connecting devices to the controlled output contact also allows you to
carry out the autotest function (enabled using "TEST FI" and "TEST FS" in
the "OPTIONS" menu) and check that the safety devices are functioning
correctly.
• The presence of the electrical current sensor does not dispense
with the obligation to install photoelectric cells and other safety devices
foreseen by the safety standards in force.
• Before connecting the appliance make sure that the voltage and
frequency rated on the data plate conform to those of the mains supply.
• For the 230 Vac power supply only use a polychloroprene 2 x 1.5 mm
+ cable that conforms to the international standard 60245 IEC 57.
• The cable may only be replaced by qualified technicians.
• An all pole trip switch with at least 3 mm between the contacts must
be installed between the unit and the mains supply.
• Don't use cables with aluminium conductors; don't solder the ends of
cables which are to be inserted into the binding posts; use cables marked
T min 85°C and resistant to atmospheric agents.
• The terminal wires must be positioned in such a way that both the
wire and the insulating sheath are tightly fastened.
ELECTRICAL CONNECTION 230 Vac
• Connect the control and security
device wires.
• Run the 230 Vac mains power
supply through the trip switch
"TS" and the through the rubber
cable clamp "PS" to the terminal
board:
- connect the live to post 1
- connect the earth to post 5
- connect the neutral to post 2 N
14
230 Vac
N L
TS
L
2