Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Pepperl+Fuchs KFD0-SD2-Ex2.1 45 Series
Summary of Contents for Pepperl+Fuchs KFD0-SD2-Ex2.1 45 Series
- Page 1 Functional Safety Solenoid Driver KFD0-SD2-Ex2.1*45 Manual ISO9001...
- Page 2 Phone: +49 621 776 - 0 E-mail: info@de.pepperl-fuchs.com North American Headquarters Pepperl+Fuchs Inc. 1600 Enterprise Parkway Twinsburg, Ohio 44087 Phone: +1 330 425-3555 E-mail: sales@us.pepperl-fuchs.com Asia Headquarters Pepperl+Fuchs Pte. Ltd. P+F Building 18 Ayer Rajah Crescent Singapore 139942 Phone: +65 6779-9091 E-mail: sales@sg.pepperl-fuchs.com https://www.pepperl-fuchs.com...
-
Page 3: Table Of Contents
Functional Safety KFD0-SD2-Ex2.1*45 Contents Introduction ............5 Content of this Document . - Page 4 Functional Safety KFD0-SD2-Ex2.1*45 Contents...
-
Page 5: Introduction
Additionally, the following parts may belong to the documentation, if applicable: • EU-type examination certificate • EU declaration of conformity • Attestation of conformity • Certificates • Control drawings • FMEDA report • Assessment report • Additional documents For more information about Pepperl+Fuchs products with functional safety, see www.pepperl-fuchs.com/sil. -
Page 6: Safety Information
Functional Safety KFD0-SD2-Ex2.1*45 Introduction Safety Information Target Group, Personnel Responsibility for planning, assembly, commissioning, operation, maintenance, and dismounting lies with the plant operator. Only appropriately trained and qualified personnel may carry out mounting, installation, commissioning, operation, maintenance, and dismounting of the product. The personnel must have read and understood the instruction manual and the further documentation. -
Page 7: Symbols Used
Functional Safety KFD0-SD2-Ex2.1*45 Introduction Symbols Used This document contains symbols for the identification of warning messages and of informative messages. Warning Messages You will find warning messages, whenever dangers may arise from your actions. It is mandatory that you observe these warning messages for your personal safety and in order to avoid property damage. -
Page 8: Product Description
Safety relevant interfaces: input 1, input 2, output 1, and output 2 • Non-safety relevant interfaces: none Note For corresponding connections see datasheet. Marking Pepperl+Fuchs Group Lilienthalstraße 200, 68307 Mannheim, Germany Internet: www.pepperl-fuchs.com KFD0-SD2-Ex2.1045, KFD0-SD2-Ex2.1245, KFD0-SD2-Ex2.1545 Up to SIL 3 Standards and Directives for Functional Safety... -
Page 9: Planning
Functional Safety KFD0-SD2-Ex2.1*45 Planning Planning System Structure 3.1.1 Low Demand Mode of Operation If there are two control loops, one for the standard operation and another one for the functional safety, then usually the demand rate for the safety loop is assumed to be less than once per year. -
Page 10: Assumptions
Functional Safety KFD0-SD2-Ex2.1*45 Planning Assumptions The following assumptions have been made during the FMEDA: • Failure rate based on the Siemens standard SN 29500. • Failure rates are constant, wear is not considered. • The safety-related device is considered to be of type A device with a hardware fault tolerance of 0. -
Page 11: Characteristic Safety Values
Functional Safety KFD0-SD2-Ex2.1*45 Planning Characteristic Safety Values Parameters Characteristic values Assessment type and Full assessment documentation Device type Mode of operation Low demand mode oder high demand mode Safety function Output is de-energized 135 FIT 0 FIT 0.08 FIT ... -
Page 12: Useful Lifetime
As noted in DIN EN 61508-2:2011 note N3, appropriate measures taken by the manufacturer and plant operator can extend the useful lifetime. Our experience has shown that the useful lifetime of a Pepperl+Fuchs product can be higher if the ambient conditions support a long life time, for example if the ambient temperature is significantly below the maximum ambient temperature. -
Page 13: Mounting And Installation
Functional Safety KFD0-SD2-Ex2.1*45 Mounting and Installation Mounting and Installation Mounting and Installing the Device Observe the safety instructions in the instruction manual. Observe the information in the manual. Observe the requirements for the safety loop. Connect the device only to devices that are suitable for this safety application. Check the safety function to ensure the expected output behavior. -
Page 14: Operation
Functional Safety KFD0-SD2-Ex2.1*45 Operation Operation Danger! Danger to life from missing safety function If the safety loop is put out of service, the safety function is no longer guaranteed. • Do not deactivate the device. • Do not bypass the safety function. •... - Page 15 Functional Safety KFD0-SD2-Ex2.1*45 Operation Proof Test Procedure Prepare a test set-up, see figure below. Verify the input and output values as given in table below. After the test, reset the device to the original settings. Step No. Input value Output value 18 V (high) ON/I current, depends on device version...
-
Page 16: Maintenance And Repair
Report all failures in the safety function that are due to functional limitations or a loss of device function – especially in the case of possible dangerous failures. In these cases, contact your local sales partner or the Pepperl+Fuchs technical sales support (service line). -
Page 17: List Of Abbreviations
Functional Safety KFD0-SD2-Ex2.1*45 List of Abbreviations List of Abbreviations Emergency Shutdown Failure In Time in 10 Failure Mode, Effects, and Diagnostics Analysis FMEDA Probability of safe failure Probability of dangerous detected failure Probability of dangerous undetected failure Probability of failures of components in the safety loop that have ... - Page 18 Pepperl+Fuchs Quality Download our latest policy here: www.pepperl-fuchs.com/quality www.pepperl-fuchs.com © Pepperl+Fuchs · Subject to modifications Printed in Germany / DOCT-8080...