Zennio EyeZen TP v2 Manual page 11

27, 36, 45, 54, 63, 72
28, 37, 46, 55, 64, 73
29, 38, 47, 56, 65, 74
30, 39, 48, 57, 66, 75
31, 40, 49, 58, 67, 76
32, 41, 50, 59, 68, 77
33, 42, 51, 60, 69, 78
34, 43, 52, 61, 70, 79
81, 97
82, 98
83, 99
84, 100
85, 101
86, 102
87, 103
88, 104
90, 106
91, 107
92, 108
93, 109
https://www.zennio.com
1 Bit I C - W - - DPT_Start
1 Bit O C R - T - DPT_Switch
1 Byte O C R - T - DPT_Scaling
1 Byte O C R - T - DPT_HVACMode
1 Bit I C - W - - DPT_Enable
1 Bit I C - W - - DPT_Enable
1 Bit I C - W - - DPT_Start
1 Bit I C - W - - DPT_Start
2 Bytes I/O C R W - - DPT_TimePeriodSec
1 Bit I C - W - - DPT_Start
1 Bit I C - W - - DPT_Enable
1 Bit I C - W - - DPT_Enable
1 Bit I C - W - - DPT_Start
1 Bit I C - W - - DPT_Start
2 Bytes I C - W - - DPT_Value_Lux
2 Bytes I C - W - - DPT_Value_Lux
1 Byte I C - W - - DPT_Scaling
1 Byte I C - W - - DPT_Scaling
2 Bytes I C - W - - DPT_Value_Lux
1 Byte I C - W - - DPT_Scaling
1 Byte O C R - T - DPT_Scaling
2 Bytes I/O C R W - - DPT_TimePeriodSec
1 Bit I C - W - - DPT_Switch
4 Bit I C - W - - DPT_Control_Dimming
1 Byte I C - W - - DPT_Scaling
1 Bit O C R - T - DPT_Switch
0/1 [Cx] External Motion Detection
0/1 [Cx] Output (Binary)
0% - 100% [Cx] Output (Scaling)
1=Comfort
2=Standby
3=Economy [Cx] Output (HVAC)
4=Building
Protection
0/1 [Cx] Lock Status
0/1 [Cx] Lock Status
0/1 [Cx] Force State
0/1 [Cx] External Switch
0 - 65535 [Cx] Length of Detection
0/1 [CLCx] External Motion Detection
0/1 [CLCx] Lock Status
0/1 [CLCx] Lock Status
0/1 [CLCx] Force State
0/1 [CLCx] External Switch
[CLCx] Setpoint
[CLCx] Setpoint During Day
0% - 100% [CLCx] Setpoint
0% - 100% [CLCx] Setpoint During Day
[CLCx] Setpoint During Night
0% - 100% [CLCx] Setpoint During Night
0% - 100% [CLCx] Dimming Value
0 - 65535 [CLCx] Length of Detection
[CLCx] Manual Control: On/Off
0/1
(Input)
0x0 (Stop)
0x1 (Dec. by 100%)
...
0x7 (Dec. by 1%) [CLCx] Manual Control: Relative
0x8 (Stop) Dimming (Input)
0xD (Inc. by 100%)
...
0xF (Inc. by 1%)
[CLCx] Manual Control: Absolute
0% - 100%
Dimming (Input)
[CLCx] Manual Control: On/Off
0/1
(Output)
1 = Motion detected by an
external sensor
Binary Value
0-100%
Auto, Comfort, Standby, Economy,
Building Protection
0 = Unlock; 1 = Lock
0 = Lock; 1 = Unlock
0 = No Detection; 1 = Detection
0 = No Detection; 1 = Detection
1-65535 s.
1 = Motion detected by an
external sensor
0 = Unlock; 1 = Lock
0 = Lock; 1 = Unlock
0 = No Detection; 1 = Detection
0 = No Detection; 1 = Detection
Setpoint Value (1-2000)
Setpoint Value (1-2000)
Setpoint Value (1-100)%
Setpoint Value (1-100)%
Setpoint Value (1-2000)
Setpoint Value (1-100)%
Dimming Value (%)
1-65535 s.
1-Bit Control
4-Bit Control
1-Byte Control
1-Bit Control
Technical Support: https://support.zennio.com
EyeZen TP v2
11