Related Manuals for Zennio EyeZen TP vT
Summary of Contents for Zennio EyeZen TP vT
- Page 1 EyeZen TP vT Motion detector with luminosity sensor for ceiling mounting ZPDEZTPVT Application program version: [1.3] User manual edition: [1.3]_a www.zennio.com...
-
Page 2: Table Of Contents
EyeZen TP vT CONTENTS Contents ............................2 Introduction .......................... 3 EyeZen TP vT........................3 Installation ........................4 Start-Up and Power Loss ....................5 Configuration......................... 6 General .......................... 6 Presence Detector ......................8 Logic Functions ......................10 ANNEX I. Communication Objects....................11 https://www.zennio.com... -
Page 3: Introduction
1 INTRODUCTION 1.1 EYEZEN TP VT EyeZen TP vT from Zennio is a device that aims at, among other functions, the detection of presence, the measurement and control of the room luminosity and the detection of occupancy within the room where it has been installed. It has been designed for ceiling or false ceiling mounting by means of the bundled accessories. -
Page 4: Installation
EyeZen TP vT 1.2 INSTALLATION EyeZen TP vT connects to the KNX bus through the on-board KNX connector. Once the device is provided with power from the KNX bus, both the individual address and the associated application program may be downloaded. -
Page 5: Start-Up And Power Loss
EyeZen TP vT 1.3 START-UP AND POWER LOSS During the start-up of the device, the detection notification LED flashes red for one minute before the motion sensor is ready. Depending on the configuration, some specific actions will also be performed during the start-up. -
Page 6: Configuration
EyeZen TP vT 2 CONFIGURATION 2.1 GENERAL After importing the corresponding database in ETS and adding the device into the topology of the desired project, the configuration process begins by entering the parameters window of the device. ETS PARAMETERISATION From General screen it is possible to activate/deactivate all the required functionality. - Page 7 EyeZen TP vT Note: the first sending after download or bus failure takes place with a delay of up to 255 seconds, to prevent bus overload. The following sendings match the period set. https://www.zennio.com Technical Support: https://support.zennio.com...
-
Page 8: Presence Detector
It also allows setting different luminosity setpoints or object types for daytime and night time as well as activating or deactivating the motion indicator LEDs. EyeZen TP vT can also set custom sensitivity of the motion sensor and measure the luminosity of the room by making certain adjustments. This measurement will be made according to the type of lens selected. - Page 9 EyeZen TP vT Figure 4. Presence Detector. Configuration. Lens Type [White / Black]. Selecting the lens type that EyeZen TP vT has installed, will allow a correct measurement of luminosity through the sensor. https://www.zennio.com Technical Support: https://support.zennio.com...
-
Page 10: Logic Functions
KNX bus, and to send the results through other communication objects specifically enabled for this purpose. EyeZen TP vT can implement up to 10 different and independent functions, each of them entirely customisable and consisting of up to 4 consecutive operations. -
Page 11: Annex I. Communication Objects
EyeZen TP vT ANNEX I. COMMUNICATION OBJECTS “Functional range” shows the values that, with independence of any other values permitted by the bus according to the object size, may be of any use or have a particular meaning because of the specifications or restrictions from both the KNX standard or the application program itself. - Page 12 EyeZen TP vT 0 = 1 = Motion detected by an 25, 35, 45, 55, 65, 75 1 Bit C - W - - DPT_Trigger [Cx] External Motion Detection external sensor 26, 36, 46, 56, 66, 76 1 Byte C R - T -...
- Page 13 EyeZen TP vT 0x0 (Stop) 0x1 (Dec. by 100%) 0x7 (Dec. by 1%) [CLCx] Manual Control: Relative 98, 114 4 Bit C R - T - DPT_Control_Dimming 4-Bit Control 0x8 (Stop) Dimming (Output) 0xD (Inc. by 100%) 0xF (Inc. by 1%)
- Page 14 Join and send us your inquiries about Zennio devices: https://support.zennio.com Zennio Avance y Tecnología S.L. C/ Río Jarama, 132. Nave P-8.11 45007 Toledo (Spain). Tel. +34 925 232 002. www.zennio.com info@zennio.com...