Related Manuals for Zennio EyeZen TP v2
Summary of Contents for Zennio EyeZen TP v2
- Page 1 EyeZen TP v2 Motion detector with luminosity sensor for ceiling mounting ZPDEZTPV2 Application program version: [1.5] User manual edition: [1.5]_a www.zennio.com...
-
Page 2: Table Of Contents
EyeZen TP v2 CONTENTS Contents ............................2 Introduction .......................... 3 EyeZen TP v2 ......................... 3 Installation ........................4 Start-Up and Power Loss ....................5 Configuration......................... 6 General .......................... 6 Motion Detector ......................8 Logic Functions ......................9 ANNEX I. Communication Objects....................10 https://www.zennio.com... -
Page 3: Introduction
1 INTRODUCTION 1.1 EYEZEN TP V2 EyeZen TP v2 from Zennio is a device that aims at, among other functions, the detection of motion, the measurement and control of the room luminosity and the detection of occupancy within the room where it has been installed. It has been designed for ceiling or false ceiling mounting by means of the bundled accessories. -
Page 4: Installation
EyeZen TP v2 1.2 INSTALLATION EyeZen TP v2 connects to the KNX bus through the on-board KNX connector. Once the device is provided with power from the KNX bus, both the individual address and the associated application program may be downloaded. -
Page 5: Start-Up And Power Loss
EyeZen TP v2 To get detailed information about the technical features of this device, as well as on the installation process and on security procedures, please refer to the corresponding Datasheet, bundled with the original packaging of the device and also available at www.zennio.com. -
Page 6: Configuration
EyeZen TP v2 2 CONFIGURATION 2.1 GENERAL After importing the corresponding database in ETS and adding the device into the topology of the desired project, the configuration process begins by entering the parameters tab of the device. ETS PARAMETERISATION From General screen it is possible to activate/deactivate all the required functionality. - Page 7 EyeZen TP v2 Figure 3. Heartbeat Note: the first sending after download or bus failure takes place with a delay of up to 255 seconds, to prevent bus overload. The following sendings match the period set. Device Recovery Objects (Send 0 and 1) [enabled/disabled]: this parameter lets the integrator activate two new communication objects (“[Heartbeat] Device...
-
Page 8: Motion Detector
It also allows setting different luminosity setpoints or object types for daytime and night time as well as activating or deactivating the motion indicator LEDs. EyeZen TP v2 can also set custom sensitivity of the motion sensor and measure the luminosity of the room by making certain adjustments. This measurement will be made according to the color of lens selected. -
Page 9: Logic Functions
KNX bus, and to send the results through other communication objects specifically enabled for this purpose. EyeZen TP v2 can implement up to 10 different and independent functions, each of them entirely customisable and consisting of up to 4 consecutive operations. -
Page 10: Annex I. Communication Objects
EyeZen TP v2 ANNEX I. COMMUNICATION OBJECTS “Functional range” shows the values that, with independence of any other values permitted by the bus according to the object size, may be of any use or have a particular meaning because of the specifications or restrictions from both the KNX standard or the application program itself. - Page 11 EyeZen TP v2 1 = Motion detected by an 27, 36, 45, 54, 63, 72 1 Bit C - W - - DPT_Start [Cx] External Motion Detection external sensor 28, 37, 46, 55, 64, 73 1 Bit C R - T -...
- Page 12 EyeZen TP v2 0x0 (Stop) 0x1 (Dec. by 100%) 0x7 (Dec. by 1%) [CLCx] Manual Control: Relative 94, 110 4 Bit C R - T - DPT_Control_Dimming 4-Bit Control 0x8 (Stop) Dimming (Output) 0xD (Inc. by 100%) 0xF (Inc. by 1%)
- Page 13 Join and send us your inquiries about Zennio devices: https://support.zennio.com Zennio Avance y Tecnología S.L. C/ Río Jarama, 132. Nave P-8.11 45007 Toledo (Spain). Tel. +34 925 232 002. www.zennio.com info@zennio.com...