Subscribe to Our Youtube Channel
Related Manuals for REMKO HITLINE TK Series
Summary of Contents for REMKO HITLINE TK Series
- Page 1 Operating and installation instructions REMKO TK series Mobile dehumidifiers TK 300 Edition EN - X07 Read the instructions prior to performing any task!
-
Page 3: Table Of Contents
Contents Air dehumidification 6-12 Safety notes Unit description Set-up Commissioning 15-17 Shutdown Unit transport Care and maintenance 18-19 Troubleshooting 19-20 Electrical wiring diagram Intended use Customer service and guarantee Environmental protection and recycling Exploded view of the unit Spare parts list Maintenance protocol Technical data R290... -
Page 4: Air Dehumidification
The mechanical heat that is released by the dehumidification The use of REMKO process is fed back into the room. air dehumidifiers Under normal use, the air Even if windows and doors dehumidifier uses approximately ■... - Page 5 REMKO air dehumidifier. and so relative humidity increases. such as brick 90-190 l/m³, heavy The air is dehumidified and, If the temperature continues to concrete 140-190 l/m³...
-
Page 6: Safety Notes
REMKO TK series The amount of energy from Condensation heat and released for condensation. evaporation heat and condensation When dehumidifying fed air, heat is the same. a larger contribution of heat is The Energy transferred to the air For water, this is:... - Page 7 The following notes must be The unit must always be switched Appropriate hazard prevention ■ ■ observed in full: off with the on/off switch. measures must be taken to The units must not be operated prevent risks to people when ■...
- Page 8 REMKO TK series Safety instructions for the The contained refrigerant R290 is Operating the units in rooms with ■ ■ colourless and odourless. operator potential ignition sources (naked flames, gas or electrical heaters, The unit must not be stored or The operational safety of the units fireplaces) is prohibited.
- Page 9 Do not allow children to play with Never cover the air inlets and out- Safety notes for installation, maintenance and inspection the unit. lets. Check the work area ■ Before starting work on units with combustible refrigerants, ensure that any potential igni- tion sources are removed and the risk of igniting the refriger- ants is eliminated.
- Page 10 REMKO TK series Remove any potential ignition Checking the electronic compo- Repairs to closed components ■ ■ ■ sources nents Before repairing closed compo- Leaking refrigerant in combina- A component and safety check nents/housing parts, the unit tion with corresponding ignition must be carried out before must be free from voltage.
- Page 11 Wiring Leak detection methods The system must be flushed with ■ ■ Lines must be checked for the The following leak detection oxygen-free nitrogen in order to following damage: methods are permitted for sys- guarantee safety. The flushing - Damage to the insulation tems with combustible refriger- process must be repeated multi- - Corrosion at the contact points...
- Page 12 REMKO TK series Labelling when shutting down ■ If a unit must be taken out of op- eration and the refrigerant must be disposed of, the unit must be labelled with the date and a signature. Ensure that the note remains attached to the combus- tible refrigerant.
-
Page 13: Unit Description
The units are used in all locations, where dry air is a must and where economic consequential damage Schematic depiction of the workings of the REMKO air dehumidifier (such as that caused by mould) must be prevented. Dehumidified... -
Page 14: Set-Up
Schematic depiction of how to set up the REMKO air dehumidifier of the unit and taking into consideration how the unit is used at its location... -
Page 15: Commissioning
Commissioning Before commissioning the unit 2. Open the air flap on the top NOTE or if local requirements dictate, of the unit. In room temperatures below the air-inlet grill and air-outlet 10 °C and relative humidity grill must be checked for 3. - Page 16 REMKO TK series Adjusting units/moisture Adjusting the discharge Automatic defrost system direction The unit’s dehumidification power The moisture contained in the is entirely dependent on the The dehumidified room air is room air condenses when cooling conditions inside the room, the discharged on the top of the unit.
- Page 17 Emptying the condensate Continuous operation with Leakage control device container external condensate outlet The unit is equipped with a leaka- The integrated condensate The units are equipped with ge control device to prevent dama- container must be emptied from a special connection nozzle on the ge in the event of refrigerant loss.
-
Page 18: Shutdown
REMKO TK series Shutdown Unit transport Use the POWER key to switch the The units are equipped with four If moisture residual remains on ■ unit off. foot rollers and an additional the evaporator or water remains handle for easy and convenient... -
Page 19: Care And Maintenance
Care and maintenance Observe the regular care and Cleaning the condenser and ■ NOTE maintenance intervals evaporator Regular care and maintenance is fundamental to a long In accordance with the The unit housing must be opened ■ service life and fault-free operating conditions, the units to allow the inside of the unit to be operation of the unit. -
Page 20: Troubleshooting
REMKO TK series Troubleshooting Filter cleaning The units are manufactured using state-of-the-art production To prevent damage to the unit, it is 5. Clean the air filter with methods and tested several times equipped with an intake grill with lukewarm water or a vacuum to verify their correct function. -
Page 21: Electrical Wiring Diagram
The unit runs but condensate The unit is loud or Note on refrigerants is not formed: condensate runs out: The units work with environmentally-friendly Check the room temperature Check whether the unit is on ■ ■ and ozone-neutral R290 The operating range of the unit a stable and even base refrigerant. -
Page 22: Intended Use
“Certificate of guarantee” Our units are carefully packed to REMKO GmbH & Co. KG at the and delivered in stable cardboard The units are only permitted time when the units are purchased transport packaging and, to be operated by people and commissioned. -
Page 23: Exploded View Of The Unit
Exploded view of the unit We reserve the right to modify the dimensions and design as part of the ongoing technical development process. -
Page 24: Spare Parts List
REMKO TK series Spare parts list Designation EDP no. Base plate Conveyor rollers Compressor, cpl. Vibration dampers Suction pipe High pressure line Centre wall Condenser (compressor) Microswitch Condensate trap Fin vaporiser Fin condenser Capillary Board housing Support plate Fan housing... -
Page 25: Maintenance Protocol
✍ Maintenance protocol Unit type: ........Unit number: ........10 11 12 13 14 15 16 17 18 19 20 Unit cleaned - outside - Unit cleaned - inside - Fan blade cleaned Fan housing cleaned Condenser cleaned Evaporator cleaned Fan function checked Air-inlet grid with filter cleaned Unit checked for damage... -
Page 26: Technical Data
REMKO TK series Technical data Series TK 300 Operating range, temperature °C 6 to 32 Operating range, humidity % RH 40 to 100 Dehumidification capacity max. l/day At 30 °C/80 % RH l/day At 20 °C/70 % RH l/day At 15 °C/60 % RH l/day Max. - Page 28 REMKO QUALITY WITH SYSTEMS Air-Conditioning | Heating | New Energies The User’s manual and specific instruction related to the safe operation of this appliance are also available in website. REMKO GmbH & Co. KG Telephone +49 (0) 5232 606-0 Hotline within Germany Klima- und Wärmetechnik...
Need help?
Do you have a question about the HITLINE TK Series and is the answer not in the manual?
Questions and answers