Related Manuals for REMKO AMT 45-E
Summary of Contents for REMKO AMT 45-E
- Page 1 REMKO AMT REMKO AMT 45-E to 115-E Air dehumidifiers Operation · Technology · Spare parts Edition GB – D09...
-
Page 3: Table Of Contents
Transportation Care and maintenance Troubleshooting Electrical wiring diagram Exploded view of the AMT 45-E unit Spare parts list AMT 45-E Exploded view of the AMT 65-E and 85-E units Spare parts list AMT 65-E and 85-E Exploded view of the AMT 115-E unit... -
Page 4: Air Dehumidification
The mechanical heat that is released by The use of the dehumidification process is fed REMKO air dehumidifiers back into the room. – Even if windows and doors Under normal use, the air are well insulated, water and... - Page 5 REMKO air dehumidifier. relative humidity increases. such as brick 90-190 l/m³, heavy The air is dehumidified and, If the temperature continues to fall, concrete 140-190 l/m³...
-
Page 6: Safety Notes
REMKO AMT Condensation heat The Energy transferred to the air but is required to convert a liquid whereby heat is consumed from the condenser consists of: into a gas. for evaporation and released Conversely, energy is released for condensation. 1. the amount of heat derived when gas is liquefied, this is beforehand in the evaporator. -
Page 7: Intended Use
"certificate of material, please consider our structural design and equipment. guarantee" to REMKO GmbH & environment. Co. KG at the time when the units Our units are carefully packed The units must only be operated are purchased and commissioned. -
Page 8: Unit Description
The units are used in all locations, where dry air is a must and where Schematic depiction of the workings of a REMKO air dehumidifier economic consequential damage (such as that caused by mould) must be prevented. -
Page 9: Set-Up
Set-up For the best economic and safe use Avoid having opened windows Electrical connection ■ of the units, the following notes and doors etc., and avoid must be followed in full: frequent entry to or exit from The units are operated ■... -
Page 10: Commissioning
Operation with a humidity local requirements dictate, the air- switch inlet grille and air-outlet grille must be checked for contamination. The REMKO humidity switch (accessories) is supplied with a special adapter. NOTE The following procedure must A contaminated grille or filter... - Page 11 10 seconds. In the AMT 45-E, the hose is The unit will switch off and connected directly to the ½" the yellow indicator light connection nozzle [D] of on the control panel will illuminate.
-
Page 12: Shutdown
REMKO AMT Shutdown AMT 115-E condensate drain Move the operating switch Due to their high dehumidification capacity, the AMT 115-E units are not to the "0" (off) position. equipped with an internal condensate container. The condensate drainage is to be provided by the customer in suitable containers via the exterior unit connection nozzles (½"). -
Page 13: Transportation
Transportation Care and maintenance For easy transportation, the units Cleaning the dust filter NOTE are equipped with 2 large Regular care and maintenance wheels and an ergonomic ATTENTION is fundamental to a long transportation and protective Check the inlet and outlet grille service life and fault-free clamp. -
Page 14: Troubleshooting
REMKO AMT Cleaning the units 9. Once cleaning has been The red indicator light completed, the unit should be (Malfunction) illuminates The unit housing must be opened dried. Take particular care with to allow the inside of the unit to be... -
Page 15: Electrical Wiring Diagram
Electrical wiring diagram AMT 45-E to 115-E Control board Lamp Operating Compressor Changeover Ambiente Probe °C Probe °C Probe °C water Fail hours valve air fan evaporator condenser water stop stop lamp Yellow Not applicable for AMT 115-E Compressor Fan motor... -
Page 16: Exploded View Of The Amt 45-E Unit
REMKO AMT Exploded view of the AMT 45-E unit 32 33 We reserve the right to modify the dimensions and design as part of the ongoing technical development process. -
Page 17: Spare Parts List Amt 45-E
Spare parts list AMT 45-E Description EDP no. Air-inlet grille 1105601 Dust filter 1105602 Transportation bracket 1105603 Fixed base cpl. 1105604 Evaporator fin package cpl. 1105905 NTC evaporator probe 1105606 NTC condenser probe 1105607 Fan housing 1105608 Fan blade 1105609 Engine mounting cpl. -
Page 18: Exploded View Of The Amt 65-E And 85-E Units
REMKO AMT Exploded view of the AMT 65-E and 85-E units We reserve the right to modify the dimensions and design as part of the ongoing technical development process. -
Page 19: Spare Parts List Amt 65-E And 85-E
Spare parts list for the AMT 65-E and 85-E units Description AMT 65-E AMT 85-E EDP no. EDP no. Air-inlet grille 1105659 1105659 Dust filter 1105660 1105660 Fixed base cpl. 1105661 1105661 Transportation bracket 1105662 1105662 Evaporator fin package cpl. 1105711 1105731 NTC evaporator probe... -
Page 20: Exploded View Of The Amt 115-E Unit
REMKO AMT Exploded view of the AMT 115-E unit We reserve the right to modify the dimensions and design as part of the ongoing technical development process. -
Page 21: Spare Parts List Amt 115-E
Spare parts list AMT 115-E Description EDP no. Air-inlet grille 1105677 Dust filter 1105678 Transportation bracket 1105679 Fixed base cpl. 1105680 Fin evaporator 1105740 Fin condenser 1105741 NTC evaporator probe 1105606 NTC condenser probe 1105607 Temperature valve 1105742 Dry filter 1105743 Fan housing 1105950... -
Page 22: Maintenance Protocol
REMKO AMT ✍ Maintenance protocol Unit type: ........Unit number: ........10 11 12 13 14 15 16 17 18 19 20 Unit cleaned - outside - Unit cleaned - inside - Fan blade cleaned Fan housing cleaned Condenser cleaned... -
Page 23: Technical Data
Technical data Series AMT 45-E AMT 65-E AMT 85-E AMT 115-E Operating range, temperature °C 3-32 3-32 3-32 3-32 Operating range, humidity % RH 40-100 40-100 40-100 40-100 Dehumidification capacity max. l/day at 30°C/80% RH l/day (DER) 37.4 (2.32) 56.8 (2.96) 70.8 (3.07) 106.4 (3.47) at 20°C/70% RH... - Page 24 REMKO, a partner who helps to solve problems. Sales REMKO offers not just a well- established sales network both nationally and internationally, but also has exceptionally highly- qualified sales specialists. REMKO employees in the field...
Need help?
Do you have a question about the AMT 45-E and is the answer not in the manual?
Questions and answers