Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for REMKO AMT Series
Summary of Contents for REMKO AMT Series
- Page 1 REMKO AMT Dehumidifier Operation · Technology ·Spare Parts Edition GB – R12...
-
Page 3: Table Of Contents
These instructions are a part of the device and must thus always be kept in the direct vicinity of the mounting site or on the device itself. Made by REMKO Subject to changes, errors and typographical errors excepted. -
Page 4: Dehumidification
REMKO AMT Dehumidification The interrelated processes that In terms of energy consumption, take place during dehumidification dehumidification has one decisive are based on physical laws. advantage: These are to be illustrated here in simplified form in order to explain Energy expenditure is restricted the principle of dehumidification. - Page 5 90-190 l/m³, REMKO dehumidifier. It is de- and the relative humidity increases. heavy concrete 140-190 l/m³, humidified and leaves the unit If the temperature falls further, the sand-lime bricks 180-270 l/m³.
-
Page 6: Safety Instruction
REMKO AMT Heat of condensation energy is released during the liq- the heat energy is recirculated, uefaction of gas, which is termed which is consumed during evapo- The energy transferred from heat of condensation. ration and released during con- the condenser to the air is densation. -
Page 7: Proper Use
„Warranty Document“ included When disposing of the packag- in delivery to REMKO GmbH & ing material, please think of the The equipment may be operated Co. KG at the time of the sale and environment. -
Page 8: Equipment Description
(e.g. through mould formation) is to be prevented. Diagram of the mode of operation of a REMKO dehumidifier The units are also suitable for dry- ing and dehumidification of: Condenser New buildings, industrial build- ■... -
Page 9: Installation
Installation For economical and reliable unit The room to be dried or dehu- Electrical connection ■ operation, the following infor- midified must be closed with mation must be followed in any respect to the ambient atmos- event: phere The equipment is ■... -
Page 10: Commissioning
Prior to each commissioning or as Control panel Operation with a hygrostat required, the air inlet and outlet must be checked for clogging. The REMKO hygrostat (accessory) is supplied with a special adapter nOTE plug. Commissioning of the units in con-... - Page 11 unit operation with hose con- Condensate 3. Carefully place the container nection outside the unit and open the Depending on the air tempera- sealing cover [F] of the drain ture and relative humidity, the opening [E]. The condensate traps [K] of the condensed water drips steadily or AMT 55 and 80-E are provided only during the defrost phases in...
-
Page 12: Shutdown
REMKO AMT Shutdown Condensate drain AMT 110-E Set the operating switch to AMT 110-E units are not provided with an internal condensate container the position „0“ (Off). due to their high dehumidification capacity. Condensate discharge must take place locally into suitable containers or via the external unit connection. -
Page 13: Unit Transport
unit transport Maintenance and Care For convenient transport, the units Cleaning the dust filter nOTE are provided with two large wheels Regular care and maintenance and an ergonomically shaped CAuTIOn is a basic precondition for a transport and protective handle. long useful life and trouble- Regularly check air inlet and This can easily be removed if... -
Page 14: Trouble Shooting
REMKO AMT Cleaning the units 9. After cleaning, the unit must be The red (Fault) pilot light il- dried. luminates For cleaning the interior of the unit Pay special attention to the and to gain access to the electri- electrical components! The cooling circuit is overloaded ■... -
Page 15: Electrical Wiring Diagram
Electrical wiring diagram AMT 0-E AMT 55-E to 110-E only AMT 110-E = Test button The test button is only intended for service and tes- ting on the control pcb. Pressing this button reduces the timer times. -
Page 16: Exploded View Amt 40-E
REMKO AMT Exploded view AMT 40-E 32 33 We reserve the right to make changes in dimensions and design in the interest of technical advances. -
Page 17: Spare Parts List Amt 40-E
Spare parts list Designation EDP no. Intake guard grille 1105601 Dustfilter 1105602 Transport handle 1105603 Basic housing complete 1105604 Finned exchange assembly, complete 1105605 NTC-thermistor, evaporator 1105606 NTC-thermistor condenser 1105607 Fan housing 1105608 Fan blade 1105609 Motor support, complete 1105610 Driving coupling 1108455 Fan motor... -
Page 18: Exploded View Amt 55-E + 80-E
REMKO AMT Exploded view AMT 55-E + 80-E We reserve the right to make changes in dimensions and design in the interest of technical advances. -
Page 19: Spare Parts List Amt 55-E + 80-E
Spare Parts List Designation AMT 55-E AMT 80-E EDP no. EDP no. Intake guard grille 1105638 1105659 Dustfilter 1105639 1105660 Basic housing complete 1105640 1105661 Transport handle 1105641 1105662 Finned exchange assembly, complete 1105642 1105663 NTC-thermistor, evaporator 1105606 1105606 NTC-thermistor condenser 1105607 1105607 Fan housing... -
Page 20: Exploded View Amt 110-E
REMKO AMT Exploded view AMT 110-E We reserve the right to make changes in dimensions and design in the interest of technical advances. -
Page 21: Spare Parts List Amt 110-E
Spare Parts List Designation EDP no. Intake guard grille 1105677 Dustfilter 1105678 Transport handle 1105679 Basic housing complete 1105680 Finned evaporator 1105681 Finned condensor 1105682 NTC-thermistor, evaporator 1105606 NTC-thermistor condenser 1105607 Thermo valve 1105683 Dry filter 1105684 Fan housing 1105685 Fan blade 1105686 Motor support, complete... -
Page 22: Maintenance Log
REMKO AMT ✍ Maintenance log Model ........Model No........10 11 12 1 1 15 1 1 18 1 20 Clean unit – surface – Clean unit – interior – Clean fan blade Clean fan housing Clean condenser Clean evaporator... -
Page 23: Technical Data
Technical data Series AMT 0-E AMT 55-E AMT 80-E AMT 110-E Working area temperature °C 3-32 3-32 3-32 3-32 % relative Working area humidity 40-100 40-100 40-100 40-100 humidity Max. dehumidification output l/day at 30°C/80 r. h. l/day (DER) 32,4 (1,88) 48,0 (2,27) 69,6 (2,69) 93,1 (2,38) - Page 24 Care is on the job. Our extensive net- work of experienced specialist retailers guarantees our customers a fast and reliable service at all times. REMKO GmbH & Co. KG Air Conditioning and Heating Technology Im Seelenkamp 12 · 32791 Lage, Germany Post office box 1827 ·D-32777 Lage...
Need help?
Do you have a question about the AMT Series and is the answer not in the manual?
Questions and answers