Rangemaster Excel 110 Ceramic Users Manual & Installation page 31

WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
When fitting new seal, position the seal join at the bottom.
Hook the new seal in one of the corner holes of the door,
and proceed round the door snapping in each hook in turn.
Slow Cook Oven door seals
There are two parts to the door seal a top 'gaol post' part,
that can be unhook in a similar way to the main oven
seals, and a separate bottom seal.
To replace the door bottom seal the door must be
removed. Remove right hand side panel (see 3). Remove
the plinths and the central vertical cover (5 screws).
Remove the two countersunk screws (1 each side)
securing the hinge arms to the front of the chamber.
NOTE: The arms are spring tensioned. Carefully remove
the door. Retain the gaskets. The door bottom seal is
now accessible and can be unclipped and replaced.
Reassemble in reverse order ensuring that the gasket
is fitted between the hinge arm and the front of the
chamber.
14. To Adjust Oven Door Catch Keep
Open oven door, slacken off locknut at base of keep, and
screw in or out as required until required fit is obtained.
Retighten locking nut.
15. To Remove Fan Oven Inner Back.
Open RH oven door and remove the screws and washers
securing the inner back to the back of the oven.
Carefully lift away the inner back. Reassemble in reverse
order making sure that the 4 screws and washers are fully
tightened. .
16. To Change Fan in Oven.
Disconnect from electricity supply.
Pull cooker forward to gain access to the rear. Remove
screws securing the electric cover to the back sheet and
remove cover. Disconnect the 3 terminals connected to the
fan noting their position. Remove oven inner back (see 15).
Hold the fan blade and remove the centre nut (left hand
thread) 2 brass washers, fan blade and circlip. Unscrew fan
retaining nuts and washers (3 off each) and lift the fan away
from the rear of the cooker. Fit new fan and reassemble in
reverse order. Check operation of oven.
17. To Remove Fan Oven Element.
Disconnect from electricity supply.
Pull cooker forward to gain access to the rear. Remove
screws securing the electric cover to the back sheet and
remove cover. Disconnect the 3 terminals connected to
the element noting their position. Remove oven inner back
(see 15). Remove 2 screws from the top of the element and
1 from the bottom of the element in side the oven. Lift out
carefully, refit new element, reassemble in reverse order.
Check operation of oven.
18. To Remove Grill Element.
Disconnect from electricity supply.
Pull cooker forward to gain access to the rear. Remove
screws securing the electric cover to the back sheet and
remove cover. Remove the 4 terminals connected to the
elements noting their position. Remove grill pan from grill
chamber. From inside grill compartment remove enamelled
front shield from grill roof, 2 screws and washers. Remove
2 screws and washers securing the grill element front
support. Remove 1 screw from each of the grill elements
and withdraw grill elements from grill chamber. Fit new
elements, reassemble in reverse order. Check operation of
grill.
19. To Remove LH Oven Elements.
Disconnect from electricity supply.
Pull cooker forward to gain access to the rear. Remove
screws securing the electric cover to the back sheet and
remove cover. Remove the 4 terminals connected to the
top element noting their position. Remove 2 screws and
washers securing the bottom element cover. Remove
the 2 terminals connected to the bottom element noting
their position. Remove 2 screws and washer from the
bottom element support. Remove 2 screws and washer
from the element bracket and withdraw the element. Fit
new element, reassemble in reverse order. Open LH oven
31