Table of Contents
Advertisement
Settlement
Insert the plug tightly.
Make sure the socket is functioning, else change to another socket.
Press power switch.
Check power supply.
Install the inlet hose again.
Tighten the connector of the machine.
Put down the drainpipe.
Straighten or clean the drainpipe.
Restart when water supply is resumed.
Open the tap.
Clean the lter according to before "clean inlet gate".
The machine is adjusting automatically.
Close the top lid.
Normal
Normal
Notes: If there is still a fault after the above checks, please pull out the plug and
contact the seller right away. It is dangerous to repair this product by yourself.
15
Other functions
Settlement
1. Give an alarm
Child-lock light ashing
synchronously.
2. Imbalance adjustment
During spinning, if the laundry is not placed equally in the tub, it would cause the machine
to vibrate violently. This machine has imbalance adjustment function and the vibration
testing system will supervise the running. Once vibration is beyond certain level,
the adjustment system will start to adjust the imbalance automatically.
3. Power supply is cut off automatically
1) Press the power supply button. If it does not start the program in 10 minutes,
the power supply will be cut off automatically.
2) After the washing is nished, the buzzer will remind, and the power supply
will be cut off automatically.
4. Child lock function
(1) If you set child lock function, all the buttons will be locked including POWER. If the top lid
is opened while the washing machine is working, the washing will stop and the machine will give an alarm.
But if you close the top lid in 5 seconds, the washing machine will stop the alarm
and continue working. If you do not close the top lid in 5 seconds, the washing machine will
begin draining if there is water in the inner tub. Even closing the top lid now will not work. During
the draining, alarm will be given every 10 seconds. When the water in the inner tub is about
5 cm higher, alarm will be given every 10 minutes (alarm is always given). When the draining
is nished, the washing machine will be in the state of waiting. If the top lid is closed, the washing
machine is unlocked and will start working as per the previous setting.
(2) Once child lock is set and the top lid is opened in 5 seconds during washing or rinse (there is water in
the inner tub), washing machine will drain and give an alarm. If you unlock the function during
draining, the washing machine will add water to setting water level and continue working.
5. Water recycle function
If you set water recycle function, after the last rinse is nished, the washing machine will not
drain and spin. The SPIN and WATER RECYCLE indicator light will ash and an alarm will be given.
The washing machine will stop working (if nobody operates, the alarm will be given every 10 minutes and
in 1 hour, power supply will be cut off automatically). When you press START/PAUSE, the WATER RECYCLE
indicator light will turn on and the washing machine will begin to drain and spin. The user can reuse the water.
Display
Explanation
The top lid is opened
E0
when preset is started.
After draining for 5 minutes,
E1
it still does not reach to
the water level.
The top lid is open while
E2
spinning.
E3
Spin does not balance.
After 40 minutes, the inlet
E4
still does not reach to the
setting water level.
E5
The top lid is opened
after setting child-lock.
Water level sensor is
F1
wrong.
16
Settlement
Close the top lid and clear up the alarm.
Open top lid, according to before
troubleshooting and settlement to
settle it, then close the top lid and
clear up the alarm.
Close the top lid and clear up the
alarm.
Open the top lid, place the laundry
equally, then close it and clear up
the alarm.
Open top lid, according to before
troubleshooting and settlement to settle
it, then close the top lid and clear up the
alarm.
Close the top lid and clear up the
alarm.
Cut the power supply and call the
technicians.
Advertisement
Table of Contents
