EWM Tetrix 352 Operating Instructions Manual page 4

Contents
Notes on the use of these operating instructions
5.2.19
5.2.20
5.2.21
5.2.22
5.2.23
5.2.24
5.3 Organising welding tasks (Mode "JOB Manager") ....................................................................... 52
5.3.1
5.3.2
5.3.3
5.3.4
5.3.5
5.3.6
5.4 Welding programs ........................................................................................................................ 55
5.4.1
5.4.2
5.4.3
5.4.4
5.4.5
5.5 Interfaces...................................................................................................................................... 57
5.5.1
5.5.2
5.5.3
5.5.4
5.5.5
5.6 Power-saving mode (Standby) ..................................................................................................... 63
5.7 Access control .............................................................................................................................. 63
5.8 Machine configuration menu ........................................................................................................ 64
5.8.1
6 Maintenance, care and disposal ......................................................................................................... 69
6.1 General ......................................................................................................................................... 69
6.2 Cleaning ....................................................................................................................................... 69
6.2.1
6.3 Maintenance work, intervals......................................................................................................... 70
6.3.1
6.3.2
6.3.3
6.4 Disposing of equipment ................................................................................................................ 71
7 Rectifying faults .................................................................................................................................... 72
7.1 Checklist for rectifying faults ........................................................................................................ 72
7.2 Warnings ...................................................................................................................................... 73
7.3 Error messages ............................................................................................................................ 74
7.4 Resetting welding parameters to the factory settings .................................................................. 75
7.5 Display machine control software version .................................................................................... 75
8 Technical data ....................................................................................................................................... 76
8.1 Tetrix 352 AC/DC ......................................................................................................................... 76
9 Accessories .......................................................................................................................................... 77
9.1 General accessories .................................................................................................................... 77
9.2 Connection cables, connection sockets ....................................................................................... 77
9.3 Options ......................................................................................................................................... 77
9.4 Transport systems ........................................................................................................................ 77
4
5.2.18.2 Automatic cut-out .......................................................................................... 43
spotArc .......................................................................................................................... 43
spotmatic....................................................................................................................... 45
Pulse welding ................................................................................................................ 46
5.2.21.1 Automated pulses .......................................................................................... 46
5.2.21.2 Thermal pulsing ............................................................................................. 47
5.2.21.3 Metallurgical pulsing (kHz pulsing) ................................................................ 48
5.2.21.4 AC special ..................................................................................................... 49
activArc ......................................................................................................................... 50
Simultaneous welding on both sides, synchronisation types ....................................... 50
5.2.23.1 Synchronisation via mains voltage (50Hz / 60Hz) ........................................ 50
Expert menu (TIG) ........................................................................................................ 51
Explanation of symbols ................................................................................................. 52
Creating a new JOB in the memory or copying a JOB ................................................. 53
Loading an existing JOB from the free memory ........................................................... 54
Resetting an existing JOB to the factory setting (Reset JOB) ...................................... 54
Resetting JOBs 1-128 to the factory setting (Reset All JOBs) ..................................... 55
Exit JOB Manager without changes ............................................................................. 55
Selection and adjustment ............................................................................................. 56
Specifying max. no. of accessible programs ................................................................ 56
Example "Program with synergetic setting" .................................................................. 57
Example "Program with conventional setting" .............................................................. 57
Accessories for switching over programs ..................................................................... 57
Connecting the robot interface / industrial bus interface .............................................. 58
5.5.1.1 RINT X12 robot interface............................................................................... 58
5.5.1.2 BUSINT X11 industrial bus interface ............................................................. 58
Connecting the PC 300.net welding parameterisation software ................................... 59
Automation interface ..................................................................................................... 60
Connection socket automation torch ............................................................................ 62
Sensor Voltage ............................................................................................................. 63
Selecting, changing and saving parameters................................................................. 64
Dirt filter ......................................................................................................................... 69
Daily maintenance tasks ............................................................................................... 70
Monthly maintenance tasks .......................................................................................... 70
Annual test (inspection and testing during operation) .................................................. 70
099-000140-EW501
28.11.2017