In these operating instructions, the designation “the power tool” always refers to the TE 80‑ATC/ TE 70‑ATC/ Always keep these operating instructions to- TE 70 combihammer or the TE 70B (available only in gether with the power tool. some regions).
Modification of the power tool or tampering with its parts is not permissible. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance.
Page 6
50% power indicator (optional) (see section “Operation”) 2.10 Items supplied as standard Power tool Side handle Grease Cleaning cloth Operating instructions Hilti toolbox 2.11 Using extension cords Recommended minimum conductor cross section and max. cable lengths Conductor cross section 1.5 mm² 2.0 mm² 2.5 mm²...
The power tool is available in various voltage ratings. Please refer to the type identification plate for details of the power tool’s voltage and power rating. Power tool TE 80‑ATC TE 70‑ATC/ TE 70/ TE 70B Rated input 1,700 W 1,600 W...
Page 8
Hammer drilling in concrete, a 22 m/s² h, HD Chiseling, a 18 m/s² h, Cheq Triaxial vibration value for the TE 70 / TE 70B (vibration Measured in accordance with EN 60745‑2‑6 vector sum) Hammer drilling in concrete, a 22 m/s² h, HD Chiseling, a 18 m/s²...
5 Safety instructions protection used for appropriate conditions will reduce 5.1 General Power Tool Safety Warnings personal injuries. WARNING c) Prevent unintentional starting. Ensure the switch is in the off‐position before connecting to power Read all safety warnings and all instructions. Fail- source and/or battery pack, picking up or carrying ure to follow the warnings and instructions may result the tool.
Page 10
Dirty or dusty power tools which have been used and could give the operator an electric shock. frequently for work on conductive materials should be checked at regular intervals at a Hilti Service Center. Under unfavorable circumstances, 5.3 Additional safety instructions dampness or dust adhering to the surface of 5.3.1 Personal safety...
tion, protective gloves and breathing protection while 5.3.5 Personal protective equipment the tool is in use. The user and any other persons in the vicinity must wear suitable eye protection, a hard hat, ear protec- 6 Before use Slide the side handle clamping band over the chuck and onto the cylindrical section at the front end of the power tool.
Page 12
the power tool to run under no load until it reaches 7.2 Operation the minimum operating temperature. If necessary, repeat this procedure until the hammering mechanism begins to operate. Turn the function selector switch until it engages in the “Hammer drilling” position. CAUTION Bring the side handle into the desired position and Working on the material may cause it to splinter.
To begin mixing, press the control switch slowly. a special connection end are used. Drill bits of this kind Press the control switch fully to continue working at are available from Hilti. For example, when the keyless full power. quick-release chuck is fitted, smooth-shank drill bits for 10.
Blinking red light See section “Troubleshooting”. damaged or when the controls do not function faultlessly. 8.4 Maintenance If necessary, the power tool should be repaired by Hilti WARNING Service. Repairs to the electrical section of the power tool may be carried out only by trained electrical specialists.
10 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. Please ask your Hilti customer service department or Hilti representative for further information.
12 EC declaration of conformity (original) Hilti Corporation, Feldkircherstrasse 100, Designation: Combihammer FL‑9494 Schaan Type: TE 80‑ATC/ TE 70‑ATC/ TE 70/ TE 70B Generation: 01/02/02/02 Year of design: 2007/2007/2007/2009 We declare, on our sole responsibility, that this product Paolo Luccini...