Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ICRealtime ICIP-3000CCD-W
Summary of Contents for ICRealtime ICIP-3000CCD-W
- Page 1 Megapixel Indoor Network Camera User’s Manual Version 4.1.1...
- Page 2 Welcome Thank you for purchasing our network camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!
- Page 3 Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction) Please note: Do not connect two power supplying sources to the device at the same time;...
- Page 4 Please shut down the device and then unplug the power cable before you begin daily maintenance work. Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device.
-
Page 5: Table Of Contents
Table of Contents General Introduction ........................1 Overview ........................1 Feature ........................... 1 Specifications ........................ 2 1.3.1 Performance ......................2 Framework ........................... 5 Rear Panel ........................5 Side Panel ........................9 Front Panel ........................9 Bidirectional talk......................10 2.4.1 Device-end to PC-end ..................10 2.4.2 PC-end to the Device-end .................. - Page 6 3G/WIFI Antenna ......................17 3.4.1 Installation......................17 3.4.2 Remove ......................... 18 I/O Port ......................... 19 Quick Configuration Tool ......................20 Overview ........................20 Operation ........................20 Web Operation .......................... 22 Network Connection ....................22 Login and Main Interface ................... 22 FAQ ............................
-
Page 7: General Introduction
1 General Introduction 1.1 Overview This series network camera integrates the traditional camera and network video technology. It adopts audio video data collection, transmission, storage together. It can connect to the network directly without any auxiliary device. This series network camera uses standard H.264 video compression technology and PCM, G.711a/u audio compression technology, which maximally guarantees the audio and video quality. -
Page 8: Specifications
Do not connect two power supplying sources to the device at the same time; it may result in device damage! Support Power over Ethernet (PoE). Conform to the IEEE802.3af standard. Connect the device to the switcher or the router that supports the PoE function to realize the network power supply. - Page 9 Main stream (1920*1080@30fps)Extra stream (704*480@30fps) H.264:56Kbps-8192Kbps, H.264H 16Kbps-8192Kbps, H.264B 56Kbps- 8192Kbps. Video Bit Rate MJPEG is adjustable and bit rate is adjustable. Support customized setup. Flip Support Mirror Support Snapshot Max 1f/s snapshot. File extension name is JPEG Privacy Mask Each channel supports max 4 privacy mask zones Video Setup Support parameter setup such as bright, contrast.
- Page 10 RS485 port PTZ control interface. Support various protocols. Power Support AC24V/DC12V power and PoE. Power <10W (For WIFI and 3G device, it is below 12W.) Consumption Working -20℃~+60℃ Temperature Working ≤95% Humidify Dimensions 70*63.2*149.5 Weight 650g Installation Support various installation modes(Enclosure and bracket are optional)
-
Page 11: Framework
2 Framework 2.1 Rear Panel This series IP camera real panel is shown as below. See Figure 2-1. The rear panel with the network port The rear panel with the 100M fiber port Figure 2-1 Rear panel Note: Picture in this chapter is for reference only and actual rear panel may vary. - Page 12 Please refer to the following sheet for detail information. Interface Name Connector Function VIDEO OUT Video output port Output analog video signal. Can connect to TV monitor to view video. AC 24V/ DC 12V Power port Power port. Input 12V DC or AC 24V ...
- Page 13 function is for some series products only. Alarm input port I/O port Alarm input port. To receive the signal from the external alarm device. Alarm output port Alarm output port. To output alarm signal to the alarm device. NO: Normal open alarm output end.
- Page 14 seconds, system can restore factory default setup. AUDIO OUT Audio output port Audio output 3.5mm Output audio signal to JACK port. the passive device such as earphone. AUDIO IN Audio input port Audio input 3.5mm Input audio signal JACK port. from devices such as pick-up.
-
Page 15: Side Panel
damage. Before hot swap, please stop record operation. Please make sure the device is securely earthed to prevent the thunderstorm strike. 2.2 Side Panel Please refer to the following interface for side panel dimension information. The unit is mm. See Figure 2-2. -
Page 16: Bidirectional Talk
Please refer to the following interface for the front panel information. The unit is mm. See Figure 2-3. Figure 2-3 Front panel 2.4 Bidirectional talk 2.4.1 Device-end to PC-end Device Connection Please connect the speaker or the MIC to the audio input port in the device rear panel. Then connect the earphone to the audio output port in the PC. -
Page 17: Alarm Input And Output Connection
Figure 2-4 Alarm The alarm setup interface is shown as below. Step 1. Connect the alarm input device to the IN alarm input port on the rear panel. Step 2. Connect the alarm output device to the NO alarm output port and C alarm output public port on the rear panel. -
Page 18: Ir Light Connection
If the type is NO, this button is normal open. The button becomes on when there is an alarm output. If the type is NC, this button is normal off. The button becomes off when there is an alarm output. Figure 2-6 Alarm output 2.5.2 IR Light Connection Note:... -
Page 19: Installation
3 Installation 3.1 Lens Installation 3.1.1 Auto Aperture Lens Please follow the steps listed below for auto aperture lens installation. The interface is shown as in Figure 3-1. Remove the CCD protection cap of the device, and then line up the lens to the proper installation position. -
Page 20: Remove Lens
and check the video is clear or not. If you cannot see the clear video, you can adjust via the flange-back. After you completed the focus setup, use the slotted screwdriver to fix the screw firmly. Fasten the focusing ring. Now the installation completed. See Figure 3-2. -
Page 21: Remove
Use the screwdriver to loosen the SD card protection screw in the rear panel, and then remove the SD card protection cap from the camera. Install the SD card to the camera according to the proper installation position. ... -
Page 22: Card
Figure 3-6 Remove SD card 3.3 3G Card 3.3.1 Installation The 3G card installation is the same with the SD card. Please follow the steps listed below to install 3G card. The interfaces are shown as Figure 3-7 and Figure 3-8. ... -
Page 23: Wifi Antenna
Figure 3-9 Remove 3G card 3.4 3G/WIFI Antenna 3.4.1 Installation Line up the thread of the screw of the 3G/WIFI antenna to the thread of the rear panel. See Figure 3-10. Please turn according to the direction in the following figure until antenna is secure firmly. See Figure 3-11. -
Page 24: Remove
Figure 3-12 3G/Wifi antenna installation 3 3.4.2 Remove Use your hands to hold the 3G/WIFI thread end and then turn according to the following figure. See Figure 3-13. Now you can see the antenna is away from the thread. See Figure 3-14. Figure 3-13 Remove 3G/Wifi antenna 1 Figure 3-14 Remove 3G/Wifi antenna 2 Remove the 3G/WIFI antenna from the port of the rear panel. -
Page 25: I/O Port
Figure 3-15 Remove 3G/Wifi antenna 3 3.5 I/O Port Install Cable Please follow the steps listed below to install the cable. See Figure 3-16. Use the small slotted screwdriver to press the corresponding button of cable groove. Insert the cable into the groove and then release the screwdriver. Remove Cable Please follow the steps listed below to remove the cable. -
Page 26: Quick Configuration Tool
4 Quick Configuration Tool 4.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 4.2 Operation Double click the “ConfigTools.exe”... - Page 27 If you want to modify the device IP address without logging in the device web interface, you can go to the configuration tool main interface to set. In the configuration tool search interface (Figure 4-1), please select a device IP address and then double click it to open the login interface.
-
Page 28: Web Operation
5 Web Operation This series network camera products support the Web access and management via PC. Web includes several modules: Monitor channel preview, system configuration, alarm and etc. 5.1 Network Connection Please follow the steps listed below for network connection. ... - Page 29 Figure 5- 2 Web login After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction. See Figure 5- 3. Figure 5- 3 Web monitoring window...
-
Page 30: Faq
6 FAQ I can not boot up Please click RESET button for at least five seconds to restore the device or can factory default setup. not control the device. SD card hot swap Before draw out SD card, please stop record or snapshot first and then wait for at least 15 seconds to remove the SD card. -
Page 31: Appendix Toxic Or Hazardous Materials Or Elements
Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBDE Circuit Board ○ ○ ○ ○ ○ ○ Component ○ ○ ○ ○ ○ ○ Case ○ ○ ○ ○ ○ ○ Wire and Cable Packing ○...
Need help?
Do you have a question about the ICIP-3000CCD-W and is the answer not in the manual?
Questions and answers