Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for IC Realtime ICIP D2010IR
Summary of Contents for IC Realtime ICIP D2010IR
- Page 1 HD IR Vandal Proof Network Dome Camera User’s Manual Version 1.2.2...
- Page 2 Welcome Thank you for purchasing our Network camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!
- Page 3 Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction) Please note: Do not connect two power supplying sources to the device at the same time;...
- Page 4 Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device.
-
Page 5: Table Of Contents
Table of Contents General Introduction ........................1 Overview ........................1 Features ......................... 1 Specifications ........................ 2 Structure ............................4 Components ........................4 Framework and Dimension ..................4 Device Installation ........................7 Installation Steps ......................7 Quick Configuration Tool ......................10 Overview ........................ -
Page 6: General Introduction
1 General Introduction 1.1 Overview This series network camera integrates the traditional camera and network video technology. It adopts video data collection, transmission together. It can connect to the network directly without any auxiliary device. This series network camera uses standard H.264 video compression technology, which maximally guarantees the video quality. -
Page 7: Specifications
Support video watermark function to avoid vicious video modification. Built-in IR light. Support IR night vision. 1.3 Specifications Please refer to the following sheet for network camera performance specification. Model ICIP D2010IR(-D) Parameter Main Processor High performance DSP Embedded LINUX System... - Page 8 396 (18*22) detection zones; sensitivity level ranges from 0 to 100; area threshold ranges from 0 to 100. Motion Detect Activation event: video storage, image snapshot, log, email SMTP and etc. Activation event: video storage, image snapshot, log, email SMTP and Video Tampering etc.
-
Page 9: Structure
2 Structure 2.1 Components You can refer to the following figure for component structure. See Figure 2-1 Figure 2-1 Component structure Please refer to the following sheet for detailed information. Component Component Name Component 1 Dome body Component 2 Dome enclosure Port Port Name Note... - Page 10 Figure 2-2 Dimension illustration (1) Figure 2-3 Dimension illustration (2)
- Page 11 Figure 2-4 Dimension illustration (3)
-
Page 12: Device Installation
3 Device Installation 3.1 Installation Steps Important Before the installation, please make sure the installation environments can at least support 3x weight of the camera. Please follow the steps listed below to install the device. Please refer to Figure 3-1 for reference. Step 1 Use inner hex wrench in the accessories bag to open dome enclosure by unfastening three inner hex screws on enclosure. - Page 13 Figure 3-1 Device installation illustration 1 Figure 3-2 Device installation illustration 2...
- Page 14 Note: When you need to reset the device, press the “Reset” button in Figure 3-2 for 10 seconds while connecting device to power. When you need to use WPS function, press the “Reset” button in Figure 3-2 for 1 to 2 seconds while connecting device to power, then press WPS button on the router.
-
Page 15: Quick Configuration Tool
4 Quick Configuration Tool 4.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 4.2 Operation Double click the “ConfigTools.exe”... - Page 16 Figure 4-3 Login prompt After you logged in, the configuration tool main interface is shown as below. See Figure 4-4. Figure 4-4 Main interface For detailed information and operation instruction of the quick configuration tool, please refer to the Quick Configuration Tool User’s Manual included in the resources CD.
-
Page 17: Web Operation
5 Web Operation This series network camera products support the Web access and management via PC. Web includes several modules: Monitor channel preview, system configuration, alarm and etc. 5.1 Network Connection Please follow the steps listed below for network connection. ... - Page 18 Figure 5- 2 Web login After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction. See Figure 5- 3. Figure 5- 3 Web monitoring window...
-
Page 19: Faq
6 FAQ I can not boot up Please click RESET button for at least 10 seconds to restore factory the device or default setup. operate properly. I can not upgrade When network upgrade operation failed, you can use port 3800 to device continue upgrade. -
Page 20: Appendix Toxic Or Hazardous Materials Or Elements
Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBDE Circuit Board ○ ○ ○ ○ ○ ○ Component ○ ○ ○ ○ ○ ○ Device Case ○ ○ ○ ○ ○ ○...
Need help?
Do you have a question about the ICIP D2010IR and is the answer not in the manual?
Questions and answers