Control Panel - Bertazzoni Professional REF BBNPTC Series User And Maintenance Manual

USE

CONTROL PANEL

1) When the appliance is switched on for the first time, it
will be operating at the following settings: 5℃ for the
fridge, 0℃ for the Fresco and -18℃ for the freezer. If you
wish to adjust the temperature or functions manually,
use the appropriate button to perform the desired
operation. The temperature range for the Fresco is from
-3℃ to 3℃.
2) Fridge temperature adjustment: Press the
the left-hand side of the control panel to adjust the
temperature within a range of between 2℃ and 8℃.
3) Freezer temperature adjustment: Press the
on the right-hand side of the control panel to adjust the
temperature within a range of between -15℃ and -25℃.
4) Fresco drawer temperature adjustment: The
controls temperature. By pressing on this button, you
can adjust the temperature within a range of between
-3℃ and +3℃. This function can be turned on/off by
pressing and holding the button for three seconds (OFF
is displayed).
5) Super Cool: Press the
and the fast cooling function is turned on. The fridge
automatically begins running at a temperature setting of
2°℃ and continues for 24 hours, after which it returns to
its normal setting and the symbol is no longer lit.
6) Holiday Mode: Press the button; the
the holiday function is turned on and the whole
appliance automatically begins running at the following
settings: fridge at 17℃ and freezer at -18℃.
7) Eco Mode: Press the
Eco function is turned on and the button lights up. The
fridge compartment runs at a setting of 5° C and the
freezer compartment runs at a setting of -18° C. The
Fresco works at a setting of 3°C.
8) Super Freeze: Press the
and the freezer begins to run the fast freezing function,
with a temperature setting of -25℃. After 24 hours, the
fast freezing function quits automatically.
9) Press and hold the power button for 3 seconds to switch
off your appliance. The button lights up and the power is
shut off. The interior lamps switch off and the
compressor stops operating. Press and hold the
button for 3 seconds to switch on your appliance. The
symbol lights up and power is restored.
button on
button; the button lights up
button lights up,
button on the control panel; the
button; the button lights up
10)No Frost models are equipped with a manual defrosting
function. Press and hold buttons
to switch on the manual defrosting function to clean the
freezer evaporator. The freezer temperature symbol
remains steadily lit. Press and hold buttons
3 seconds to switch off the manual defrosting function.
The freezer temperature symbol goes dark.
11)Fault Display: This appliance has a "Fault Display &
Alarm" function. Once the sensors detect a fault, alerts
are shown on the temperature display; the appliance still
cools, but a professional service engineer should be
button
called in to check it.
• F2 – Fresco sensor
• F3 – Fridge compartment sensor
button
• F4 – Freezer compartment sensor
• F5 – Defrosting sensor
• 2E – Freezer fan/motor fault
• CE– Communication fault between main board and
display panel
The above Faults are only shown on the display; there
is no audible alarm signal.
Maximum freezer temperature exceeded alarm: If, after the
freezer reaches the set temperature, the temperature rises
to above -1℃, the alarm will sound, accompanied by
simultaneous flashing of the freezer temperature display.
Press any button to cancel the audible alarm. The flashing
will continue until the temperature falls below -1℃.
NOTE
The
compressor compartment.
POSITION
5℃ / -18℃
5℃ / -18℃
+
main board is located
CONDITIONS
Summer or ambient
temperature
between 25-35℃
Spring, autumn or ambient
temperature
between 15-25℃
Fig. 3
for 5 seconds
+ for
in the
11