Wiring Opening Device Options; Learn Unlearned Sensor Inputs - Max 1200FS pro Installation Manual

11

wiring opening device options

250 mA Max.
12 VDC
OR
12V Power
24 VDC
Radio
Power
Stand-Alone Keypad
less than 200 mA
Radio Receivers
Emergency Open Device
Emergency OPEN
(Overrides gate
disable switch)
12

LEARN unlearned sensor inputs

Indicated Inputs MUST be "LEARNED" before gate operator will MONITOR those sensors.
1. Sensors that have been wired to indicated inputs MUST be "LEARNED" BEFORE they will be MONITORED.
2. Press and HOLD the STOP button & then the OPEN button together until beeping is heard, learn mode begins.
DO NOT press the OPEN button before the STOP button or learn mode will NOT begin (no beeping).
NOTE: Sensors wired to the
They are "AUTOMATICALLY
3. LEDs WILL turn ON for each detected "LEARNED" sensor that has been wired to the inputs.
If a sensor's LED is NOT on, that sensor has a problem and it MUST be corrected before continuing.
Possible problems:
• Photocells are out of alignment
• Photocells are wired wrong - N.C. or N.O. depending on which photocells are used
• Sensor is bad
When all LEDs are ON that should be ON, proceed to next step.
4. Press STOP button again within 5 min. to learn sensors and end learn mode, beeping stops.
Wired "Learned" Inputs will now be MONITORED.
NOTE: If STOP button is not pressed within 5 min., learn mode terminates.
If no "LEARNED" sensors are detected then factory default setting is restored (Inputs will NOT be Monitored).
BATTERY
BATTERY VOLTAGE
INPUT
E 1/2 F
ERROR
BATTERY
BATTERY
INPUT
BACKUP MODE
BATTERY
LEAVE OPEN
IN USE
OPEN 1 TIME
REPLACE
LEAVE
BATTERY
BATTERY
POWER / CLOSED
TEST
POWER
SOLAR IN
ERD SENSITIVITY
14 12 14 12
16 16
MIN MIN
ERD
1 9 1
MAX MOTOR MAX
MODULE
SENSE OVER SENSE
3 7 3
PORT
LOAD
OPENING CLOSING
OBD PORT
RESET /
BLACK BOX
MATRIX III
MANUAL
RELEASE OFF
SWING / SLIDE
1
2
ALARM 3
4
5 MOTION CONTROL
PROGRAMMING
ID PLUG
6
ERROR
1
2
3
ID
4
PLUG
5
6
7
OPEN STOP
PROGRAM
8
9
10
OFF
QUICK
EXIT PWR OPEN
SOLAR MODE
CLOSE LEFT
EXIT LOOP
OFF ON
GND
OFF ON
CENTER LOOP
LOOP PWR
GATE SPEED
SAFETY LOOP OPERATOR
MIN MIN
FAULTS
MAX MAX
PRIMARY SECONDARY
24VDC OUTPUT
GND OPENING
12VDC OUTPUT
GND
LINK
OK
PRIMARY/
SECONDARY
LINK
Dry Contact
(N.O.)
Telephone
(N.O.)
Dry Contact (N.O.)
PHOTO CLS NC input and OPEN ONLY NC
MONITORED".
MATRIX III
MOTOR
INPUTS
MOTOR
POSITION
INPUTS
CLOSE
TIMER
SLIDER
ERD
LIMIT
9
MOTOR
OVER
7
SWING
LOAD MIN MAX
OFF
LIMIT
ON/OFF
BATTERY
JOG
GATE OPEN
COM
GATE CLOSED
GND
LEFT RIGHT
NO
CLOSE MAG
LOCK COM
NC
MAGLOCK
OPEN
RIGHT DELAY
OPEN ONLY NC
PHOTO CLS NC
GATE
OFF 2.5 sec OPEN/CLS NC
External Alarm
1.5 sec
12VDC OUT
GND
Reset Button
OPEN ONLY 10K
UL
ENTRAP CLS ONLY 10K
CLOSING
OPEN/CLS 10K
12VDC OUT
GND
Com
Normal Opening Devices
Key Switch Card Reader
Separate power
for Devices if required.
Entry
input do NOT need to be "Learned".
UL 325 2018 Standard - MAX 1200 FS PRO/1700 FS PRO Matrix III Install Version 2c
12
Maglock
Bi-parting gates using locks:
- +
Primary gate opens FIRST. Install
-
lock accordingly to account for this.
+
MAGLOCK LED (Monitors Maglock):
ON - Locked
Flashing - Problem with Maglock Power.
You MUST select a time delay when using
a maglock. Maglock power disengages 1.5
sec or 2 sec before gate starts opening.
Dual Gate Operators using Maglock:
S
E S
P R
Primary gate opens FIRST. Install maglock
T
S E
R E accordingly to account for this.
t o
Stop
(N.O.) Manual Release
Keypad
Safety Open Device
(N.O.)
Dry Contact
MOTION CONTROL
OPEN STOP
CLOSE
OPEN ONLY NC
Factory Learned Input
PHOTO CLS NC Factory Learned Input
Unlearned Input
OPEN/CLS NC
12VDC OUT
GND
O O O O O OPEN ONLY 10K
Unlearned Input
C C CLS ONLY 10K Unlearned Input
Unlearned Input
OPEN/CLS O O 10K
12VDC OUT
GND
MOTION CONTROL
STOP
OPEN CLOSE
Gnd
-
+
NO
Solenoid Lock
OFF - Unlocked
MAGLOCK DELAY:
Key will manually
release slide gate
Safety Device
MAX OPEN Switch
(Overrides gate
disable switch)