Middle Atlantic Products Credenza Rack C5 Series Assembly Instructions Manual
Hide thumbs
Also See for Credenza Rack C5 Series:
- Instruction sheet (15 pages) ,
- Assembly instructions manual (9 pages) ,
- Installation instructions (4 pages)
Advertisement
Quick Links
assembly instructions
C5 SERIES
CREDENZA RACK
THANK YOU
Thank you for purchasing the C5 Credenza Rack. Please read all instructions thoroughly before
assembling this product.
WARNING: Instructions for C5 Series accessories MUST be read thoroughly prior to following these
instructions. Please see the accessory-specific instructions for details on proper assembly.
PRODUCT FEATURES
- Built-in thermostatically controlled cooling
- Welded rack frame ships separate to allow for equipment integration before finished surfaces are
attached
- Weight rating of 800 pounds, including finishing kit*, with maximum 350 pounds located on
top surface (*Middle Atlantic Products supplied finishing kit is 200 pounds complete)
- 14 rackspaces per bay
- Factory installed casters
I-00439
Rev G
Advertisement
Related Manuals for Middle Atlantic Products Credenza Rack C5 Series
Summary of Contents for Middle Atlantic Products Credenza Rack C5 Series
- Page 1 - Welded rack frame ships separate to allow for equipment integration before finished surfaces are attached - Weight rating of 800 pounds, including finishing kit*, with maximum 350 pounds located on top surface (*Middle Atlantic Products supplied finishing kit is 200 pounds complete) - 14 rackspaces per bay - Factory installed casters...
-
Page 2: Kickplate Installation
KICKPLATE INSTALLATION 1) Install the Kickplate by aligning screws into place using keyholes on credenza frame. FRONT VIEW Kickplate secures into place when shifted in direction of arrow REAR VIEW Page 2... -
Page 3: Side Panel Installation
SIDE PANEL INSTALLATION NOTE: For accessories related to the Side Panels, please read those instructions thoroughly before continuing with the installation below 2) Install Side Panels by placing the four pre-installed hooks into the four slots on the frame. (FIGURE A) NOTE: When installing side panels, ensure door hinge plates are located at the front of the frame. - Page 4 TOP SURFACE INSTALLATION NOTE: If using the C5MM1 Series Universal Monitor Mounts, please read those instructions thoroughly before continuing with the installation below. 3) Attach Top Surface to the frame using provided screws. Extra screws provided. (FIGURE B) NOTE: Flat edge of Top Surface is designated as the rear. (FIGURE B) (Side Panel removed for clarity) Number of #10 x 5/8”...
- Page 5 DOOR INSTALLATION ONTO SIDE PANEL 4) Install doors using provided screws (two places per door) as shown. Extra screws provided. (FIGURE C) NOTE: All Doors may be installed to swing open from either left or right. Factory Installed Bumpers (NOTE: (6) Six replacement bumpers supplied) (FIGURE C) Page 5...
- Page 6 DOOR INSTALLATION ONTO MULLION 5) Door to be installed onto credenza frame using provided screws (two places per door) as shown. (FIGURE D) (FIGURE D) (Additional Sides and Doors removed for clarity) Page 6...
- Page 7 HINGE ADJUSTMENTS Door in open position (FIGURE E) NOTE: Directional adjustments apply to the door in the closed position. Hinge adjustment is done with door in open position. Refer to (FIGURE E) for appropriate adjustments Side Adjustment: Adjusts horizontal placement of door. Adjusts door-to-door gap - Rotate screw clockwise or counterclockwise (+/-0.06 in) [+/-1.5 mm] Height Adjustment: Adjusts vertical height of door - Loosen to align door, then tighten (+/-0.08 in) [+/-2 mm]...
- Page 8 HANDLE/KNOB INSTALLATION Depending on credenza style (traditional or contemporary), handles and knobs are installed into pre-drilled holes shown in the figures provided. (FIGURE F) (Contemporary Handle - 2 screws) (Traditional Knob - 1 screw) (FIGURE F) LACER BAR RELOCATION Pre-installed Lacer Bars can be relocated on frame by removing screws as shown. (FIGURE G) (FIGURE G) Page 8...
- Page 9 DIMENSIONS ” [631 mm] ” ” 43” [631 mm] [1655 mm] [1092 mm] ” [749 mm] ” [749 mm] 2-Bay 3-Bay ” ” [19 mm] ” [555 mm] ” [531 mm] [631 mm] ” [749 mm] ” [625 mm] 1-Bay Door ”...
- Page 10 WARRANTY Middle Atlantic Products, Inc. (the "Company") warrants the C5 Credenza Frame to be free from defects in material or workmanship under normal use and conditions for the lifetime of the product, the Cladding for (7) seven years, and the Fans for (3) three years from the date of shipment by the Company.